Comparing Gud Parameters (Regarding Measuring Functions) - Siemens SINUMERIK 840D sl Programming Manual

A.4

Comparing GUD parameters (regarding measuring functions)

You can make specific basic settings per cycle machine, setting data (MD, SD).
The following prefixes are defined:
● §SNS_... Generally applicable setting data
● §SCS_... Channel-specific setting data
● §MNS_... Generally applicable machine data
● $MCS_... Channel-specific machine data
The GUD parameters listed in the following table represent the contents of the GUD blocks
GUD5, GUD6 and GUD7_MC up to version V7.5 where equivalent MD/SD is available as from
version V2.7 / V4.4.
The GUD are backwards compatible with existing measuring programs regarding their use.
The GUD5, GUD6 and GUD7_MC modules are replaced by the PGUD (SGUD in the parameter
display).
GUD up to Version 7.5 From MD/SD version V2.7/V4.4
_WP[x,0]
_WP[x,1]
_WP[x,2]
_WP[x,3]
_WP[x,4]
_WP[x,5]
_WP[x,6]
_WP[x,7]
_WP[x,8]
_WP[x,9]
_WP[x,10]
_KB[x,0]
_KB[x,1]
_KB[x,2]
_KB[x,3]
_KB[x,4]
_KB[x,5]
_KB[x,6]
_TP[x,0]
_TP[x,1]
_TP[x,2]
_TP[x,3]
_TP[x,4]
_TP[x,5]
Measuring cycles
Programming Manual, 12/2017, 6FC5398-4BP40-6BA1
A.4 Comparing GUD parameters (regarding measuring functions)
SD54600 $SNS_MEA_WP_BALL_DIAM[0...11]
SD54601 $SNS_MEA_WP_TRIG_MINUS_DIR_AX1[0...11]
SD54602 $SNS_MEA_WP_TRIG_PLUS_DIR_AX1[0...11]
SD54603 $SNS_MEA_WP_TRIG_MINUS_DIR_AX2[0...11]
SD54604 $SNS_MEA_WP_TRIG_PLUS_DIR_AX2[0...11]
SD54605 $SNS_MEA_WP_TRIG_MINUS_DIR_AX3[0...11]
SD54606 $SNS_MEA_WP_TRIG_PLUS_DIR_AX3[0...11]
SD54607 $SNS_MEA_WP_POS_DEV_AX1[0...11]
SD54608 $SNS_MEA_WP_POS_DEV_AX2[0...11]
SD54609 $SNS_MEA_WP_STATUS_RT[0...11]
SD54610 $SNS_MEA_WP_STATUS_GEN[0...11]
SD54621 $SNS_MEA_CAL_EDGE_PLUS_DIR_AX2[0...2]
SD54622 $SNS_MEA_CAL_EDGE_MINUS_DIR_AX2[0...2]
SD54615 $SNS_MEA_CAL_EDGE_BASE_AX1[0...2]
SD54617 $SNS_MEA_CAL_EDGE_PLUS_DIR_AX1[0...2]
SD54618 $SNS_MEA_CAL_EDGE_MINUS_DIR_AX1[0...2]
SD54620 $SNS_MEA_CAL_EDGE_UPPER_AX2[0...2]
SD54619 $SNS_MEA_CAL_EDGE_BASE_AX2[0...2]
SD54625 $SNS_MEA_TP_TRIG_MINUS_DIR_AX1[0...5]
SD54626 $SNS_MEA_TP_TRIG_PLUS_DIR_AX1[0...5]
SD54627 $SNS_MEA_TP_TRIG_MINUS_DIR_AX2[0...5]
SD54628 $SNS_MEA_TP_TRIG_PLUS_DIR_AX2[0...5]
SD54629 $SNS_MEA_TP_TRIG_MINUS_DIR_AX3[0...5]
SD54630 $SNS_MEA_TP_TRIG_PLUS_DIR_AX3[0...5]
Changes from cycle version SW4.4 and higher
351