Dell C9000 Series Networking Configuration Manual page 352

ERROR: Unit 0 hg port 30 is DOWN
ERROR: Unit 0 hg port 31 is DOWN
ERROR: Unit 0 hg port 32 is DOWN
hgLinkStatusTest ............................................ FAIL
Starting test: i2cTest ......
ERROR: ioctl: "SFP0" op(1)=READ WITH STOP bus=9 address=0x50 offset=0 length=1
ERROR: ioctl: "SFP1" op(1)=READ WITH STOP bus=10 address=0x50 offset=0 length=1
ERROR: ioctl: "SFP2" op(1)=READ WITH STOP bus=11 address=0x50 offset=0 length=1
ERROR: ioctl: "SFP3" op(1)=READ WITH STOP bus=12 address=0x50 offset=0 length=1
ERROR: ioctl: "SFP4" op(1)=READ WITH STOP bus=13 address=0x50 offset=0 length=1
ERROR: ioctl: "SFP5" op(1)=READ WITH STOP bus=14 address=0x50 offset=0 length=1
i2cTest ..................................................... FAIL
Starting test: opticEepromTest ......
ERROR: optic:1 is not present
ERROR: optic:5 is not present
ERROR: optic:9 is not present
ERROR: optic:13 is not present
ERROR: optic:17 is not present
ERROR: optic:21 is not present
opticEepromTest ............................................. FAIL
opticPhyTest ................................................ PASS
Starting test: opticPresenceTest ......
ERROR: optic:1 is not present
ERROR: optic:5 is not present
ERROR: optic:9 is not present
ERROR: optic:13 is not present
ERROR: optic:17 is not present
ERROR: optic:21 is not present
opticPresenceTest ........................................... FAIL
Starting test: pcieScanTest ......
17 PCI devices installed out of 17
pcieScanTest ................................................ PASS
rtcTest ..................................................... PASS
sataSsdTest ................................................. PASS
Starting test: showTemperature ......
+Board First Thermal Monitor Sensor[0] is 42.0 C
+Board First Thermal Monitor Sensor[1] is 37.0 C
+Board First Thermal Monitor Sensor[2] is 36.0 C
+Board First Thermal Monitor Sensor[3] is 37.0 C
CPU Temp 31 c
DDR Temperature 35 c
showTemperature ............................................. PASS
slotInfoTest ................................................ PASS
Starting test: spiFlashAccessTest ......temperature monitor 0: current= 49.8,
peak= 86.1
temperature monitor 1: current= 50.9, peak= 86.1
temperature monitor 2: current= 51.4, peak= 87.8
temperature monitor 3: current= 52.0, peak= 87.8
temperature monitor 4: current= 50.3, peak= 87.8
temperature monitor 5: current= 49.8, peak= 87.8
temperature monitor 6: current= 50.9, peak= 88.8
temperature monitor 7: current= 50.3, peak= 88.3
temperature monitor 8: current= 50.9, peak= 89.4
average current temperature is
maximum peak temperature is 89.4
spiFlashAccessTest .......................................... PASS
Starting test: udfLinkStatus ......
ERROR: Unit 0 xe port 26 is DOWN
udfLinkStatus ............................................... FAIL
xeLinkSpeedTest ............................................. PASS
Starting test: xeLinkStatusTest ......
ERROR: Unit 0 xe port 1 is DOWN
ERROR: Unit 0 xe port 5 is DOWN
ERROR: Unit 0 xe port 9 is DOWN
50.7
Debugging and Diagnostics 352