Cb1_Cont-A; Cb1_Cont-B - Toshiba GRL100-701B Instruction Manual

Further, all binary input functions are programmable by PLC (Programmable Logic Controller)
function.
The default setting of the binary input is shown in Table 3.2.1.2.
Module
BI No.
Name
IO#1 BI1 CB1 AUXILIARY CONTACT - A Ph
BI2 CB1 AUXILIARY CONTACT - B Ph
BI3 CB1 AUXILIARY CONTACT - C Ph
BI4 CB2 AUXILIARY CONTACT - A Ph
BI5 CB2 AUXILIARY CONTACT - B Ph
BI6 CB2 AUXILIARY CONTACT - C Ph
BI7 DISCONNECTOR NORMALLY CLOSED 1542
BI8 DISCONNECTOR NORMALLY OPEN
BI9 SIGNAL RECEIVE (R1)
BI10 SIGNAL RECEIVE (R2)
BI11 (*) DC POWER SUPPLY
BI12 TRANSFER TRIP COMMAND 1
BI13 TRANSFER TRIP COMMAND 2
BI14 DEF SIGNAL RECEIVE (R1)
BI15 DEF SIGNAL RECEIVE (R2)
IO#2 BI16 EXTERNAL TRIP - A Ph
BI17 EXTERNAL TRIP - B Ph
BI18 EXTERNAL TRIP - C Ph
IO#3 BI19 CARRIER PROTECTION BLOCK
BI20 EXTERNAL CB CLOSE COMMAND
BI21 INDICATION RESET
BI22 CB1 AUTORECLISNG READY
BI23 CB2 AUTORECLISNG READY
BI24 AUTORECLOSING BLOCK COMMAND
BI25 Spare
BI26 Spare
BI27 Spare
BI28 Spare
IO#4 BI34 Spare
BI35 Spare
BI36 Spare
Note (∗): If the binary input of DC power supply is OFF, the ready signal of relay is OFF and the
message 'Term∗ rdy off' is displayed. See Section 3.3.6.
(+)
(−)
[BISW1]
BI1
BI1
[BISW2]
BI2
BI2
[BISWn]
BIn
BIn
Table 3.2.1.2 Binary Input Signals
Contents
BI1 command
"Norm"
1
"Inv"
BI2 command
"Norm"
1
"Inv"
BIn command
"Norm"
1
"Inv"
1
0V
Figure 3.2.1.1 Logic Level Inversion
 170 
Setting
Signal No. & Signal Name
1536

CB1_CONT-A

1537

CB1_CONT-B

1538 CB1_CONT-C
1539 CB2_CONT-A
1540 CB2_CONT-B
1541 CB2_CONT-C
DS_N/O_CONT
1543 DS_N/C_CONT
1856 CAR.R1-1
1864 CAR.R2-1
1546 DC_SUPPLY
1547 85S1
1548 85S2
1857 CAR.R1-2
1865 CAR.R2-2
1551 EXT_TRIP-A
1556 EXT_CBFIN-A See the BISW setting
1552 EXT_TRIP-B in Relay setting sheet
1557 EXT_CBFIN-B
1553 EXT_TRIP-C
1558 EXT_CBFIN-C
1544 CRT_BLOCK
1545 CB_CLOSE
1549 IND.RESET
1571 CB1_READY
1572 CB2_READY
1573 ARC_RESET
Signal No.
PLC logic
6 F 2 S 0 8 5 0
Norm or Inv
Protection
schemes