Table of Contents
Advertisement
PROGRAMMING PROCEDURES
SECTION 200-255-308
JANUARY 1993
CHAPTER 8
MESSAGE
CENTER DATA
will allow
internal
DTMF
signaling
to
these ports.)
1. Message
Center
Data Block (Table
8-1)
NOTE:
If using a Toshiba
INTOUCH
Digital
Voice
1.01 The
Message
Center
Data
Block (DMCD
Messaging
System,
do not make any entries
Program)
identifies
the type of Message
Center
for the MDNO and MDNI
prompts.
Press the
and its location.
q
key,
REQ (Request)-Indicates
that the program
has
loaded.
Two responses
are possible:
NEW-To
create a new Data Block.
CHG-To
alter an existing Data Block.
MWCO (Message
Center
#0)-Identifies
the type
of Message
Center.
Enter: MC (Message
Center)
or VM (Voice
Mail).
DSCO (Disconnect
Code)-Defines
the discon-
nect code of the voice mail equipment
for Mes-
Enter:
XXXX or NONE.
sage Center
#O. (This prompt
will only appear
when MWCO =VM.) This disconnect
code is sent
to voice mail equipment
for disconnect
before
the voice mail timeout
occurs, and it must match
the code that is programmed
in the voice mail
svstem.
MWCI
(Message
Center
#I )-Identifies
the type
of Message
Center.
(This prompt
will only ap-
pear if TEN = Y in the DSYS Data Block.)
Enter: MC (Message
Center)
or VM (Voice
Mail).
MDNO (Message
Center
#0 DN)-Identifies
direc-
tory numbers
of Message
Center #O. An "A" will
follow the MDNO prompt
and any entries made
will be added. To delete a port, press the carriage
return (m
key. The system will then prompt "D"
and any entries made will be deleted.
Enter:
1 - 4 digits for each DN, or ATTO.
(ATT0 or electronic/digital
telephone
DN
is valid only if MWCO = MC. If MWCO =
VM, then up to 32 standard
telephone
[NSTUJ port DNs can be entered.
This
will allow
internal
DTMF
signaling
to
these ports.)
MDNl
(Message
Center
#l DN)-Identifies
direc-
tory numbers
of Message
Center #l . This prompt
will appear
only in tenant
systems.
An "A" will
follow the MDNl
prompt
and any entries made
will be added. To delete a port, press the carriage
return (m
key. The system will then prompt "D"
and any entries
made will be deleted.
Enter: 1 - 4 digits for each DN, or ATT1 .
(ATT1 or electronic/digital
telephone
DN
is valid only if MWCl
= MC. If MWCI
=
VM, then up to 32 standard
telephone
[NSTU]
port DNs can be entered.
This
DSCI
(Disconnect
Code)--Defines
the discon-
nect code of the voice mail equipment
for Mes-
sage Center
#1. (This prompt
will only appear
when MWCl = VM.) This disconnect
code is sent
to voice mail equipment
before
the voice mail
timeout
occurs, and it must match the code that
is programmed
in the voice mail system.
Enter:
XXXX or NONE.
NM0
(Toshiba
Voice Messaging
#O)-If
using a
Toshiba
INTOUCH
or VP Digital Voice Messag-
1
ing System,
enter up to 32 directory
numbers
(NSTU ports) that will be connected
to the IN-
TOUCH
or VP system. This provides enhanced
1
integration
of the PERCEPTIONehex
and IN-
TOUCH
or VP systems.
Following
the NM0
1
prompt, the PERCEPTlONe
or PERCEPTION,,
system will prompt
an "A." Any entries made will
be added.
To delete
a port, press the carriage
return m)
key. The system will then prompt
a
"D" and any entries
made will be deleted.
Enter: XXXX XXXX...
(in response
to the A
prompt).
XXXX XXXX...
(in response
to the D
prompt).
TVMl
(Toshiba
Voice
Messaging
#1)-This
prompt
will only appear
in tenant
systems.
If
using a Toshiba
INTOUCH
or VP Digital Voice
1
Messaging
System,
enter
up to 32 directory
numbers
(NSTU ports) that will be connected
to
8-1
Advertisement
Chapters
Table of Contents
