Index - ABB SmartTouch B/stainless Product Manual

17

Index

A
ABB DCA SmartTouch 10 ETS app
Installation ...................................................................... 69
ABB-free@home ®
initial commissioning ................................................. 44, 45
Access to pages ........................................... 343
Activating mute (mite timer) ........................... 349
Add device .................................................. 49
Additional cooling stage ................................. 259
Additional cooling stage — Control value difference for
sending of cooling control value .................... 259
Additional cooling stage — Cyclic sending of the
control value ........................................... 260
Additional cooling stage — Hysteresis ................. 260
Additional cooling stage — Maximum control value (0 -
255) ...................................................... 260
Additional cooling stage — Minimum control value for
basic load (0 - 255) ................................... 260
Additional cooling stage — Mode of the control value
........................................................... 259
Additional heating stage ................................. 248
Additional heating stage — Control value for sending of
heating control value ................................. 248
Additional heating stage - Cyclic sending of the control
value .................................................... 249
Additional Heating Stage - Hysteresis (x 0.1°C) ..... 249
Additional heating stage — Maximum control value (0 -
255) ...................................................... 249
Additional heating stage — Minimum control value for
basic load (0 - 255) ................................... 249
Additional heating stage — Mode of control value .. 248
Additional necessary components ....................... 27
Additional stage cooling — PWM cycle cooling . 254, 259
Additional stage heating - PWM cycle heating . 243, 248
Addressing ............................................ 40, 381
Alarm functions ........................................... 277
Alarm functions - Condensate water alarm ........... 277
Alarm functions — Dew point alarm ................... 277
Alarm functions - Frost alarm temperature for HVAC
and RHCC status (°C) ................................. 277
Alarm functions - Heat alarm temperature for RHCC
status (°C) .............................................. 277
Allocation of devices ...................................... 48
Application
"Door communication" .......................................... 108, 210
"Fault and alarm messages" ......... 109, 213, 215, 216, 354
"Favourite control elements" ......................................... 112
"Internal RTC" ............................................... 112, 116, 237
"Logical functions" ................................................ 111, 225
"Presence simulation" ........................................... 110, 222
"Scene actuator" ................................................... 110, 217
"Time programs" ................................................... 111, 224
Application................................................. 282
Application "Door communication"
Page protected by PIN ................................................. 210
Product manual 2CKA001473B5343
Use of control elements ................................................210
Use of door communication ..........................................210
Application "Fault and alarm messages"
Automatic archiving at an acknowledgement ................214
Default setting for signal tone volume [%] .....................214
Enable export ................................................................213
Name of message .........................................................215
Page PIN-protected.......................................................213
Signal tone for error ......................................................214
Sound for alarm.............................................................214
Sound for Notice ...........................................................214
Type of alarm ................................................................215
Type of message...........................................................215
Use of fault and alarm messages..................................213
Application "Logic functions"
Channel x - Application .................................................225
Application "Presence simulation"
Delay time up to activation ............................................223
Enable export ................................................................222
Page protected by PIN ..................................................222
Setting the object type...................................................223
Use of presence simulation ...........................................222
Application "Scene actuator"
Name of scene ..............................................................221
Name of scene actuator ................................................217
Number of participants ..................................................217
Number of scenes .........................................................217
Object type x .................................................................218
Object x is to be changed..............................................221
Overwriting scenes during download ............................217
Scene number ...............................................................221
Start light scene with ... .................................................221
Storing light scene.........................................................221
Telegram delay .............................................................217
Application "Time programs"
Overwriting time programs ............................................224
Page protected by PIN ..................................................224
Applications
Parameters............................................................100, 122
Applications and application pages
Configuration .................................................................108
Audio control" control element
Use random playback ...................................................200
B
Basic load active when controller is off .............. 262
Basic stage cooling ....................................... 253
Basic stage cooling — Cyclic sending of the control
value .................................................... 253
Basic stage cooling — Hysteresis ....................... 254
Basic stage cooling — Maximum control value (0 - 255)
.......................................................... 254
Basic stage cooling — Minimum control value for basic
load (0 to 255) ........................................ 254
Basic stage cooling — Mode of thre control value ... 253
Basic stage cooling — Status object cooling ......... 253
Index
│362