Siemens 6RA7086-6KS22 Operating Instructions Manual page 519

05.05
PNU Description
P494 Motor temperature analog 2 (temperature sensor at terminals 204 /
* 205): Tripping of alarm or fault message
FDS
Motor temperature grasped with KTY84
0 Monitoring deactivated
(G185)
1 Alarm (A029) at temperature > P491
2 Fault message (F029) at temperature > P492
3 Alarm (A029) at temperature > P491 and
fault message (F029) at temperature > P492
Motor temperature grasped with PTC thermistor
0 Monitoring deactivated
1 Alarm message (A029) when operating point of PTC thermistor
is reached
2 Fault message (F029) when operating point of PTC thermistor is
reached
3 Illegal setting
P495 Brush length sensing: Tripping of alarm or fault message
*
0 No brush length sensing (terminal 211 is not scanned)
FDS
1 Binary brush length sensing (terminal 211 is scanned)
Alarm (A025) in response to 0 signal
(G186)
2 Binary brush length sensing (terminal 211 is scanned)
Fault message (F025) in response to 0 signal
P496 Bearing condition: Tripping of alarm or fault message
*
0 No bearing condition sensing (terminal 212 is not scanned)
FDS
1 Bearing condition sensing (terminal 212 is scanned)
Alarm (A026) in response to 1 signal
(G186)
2 Bearing condition sensing (terminal 212 is scanned)
Fault message (F026) in response to 1 signal
P497 Air flow: Tripping of alarm or fault message
*
0 No air flow monitoring (terminal 213 is not scanned)
FDS
1 Air flow monitoring (terminal 213 is scanned)
Alarm (A027) in response to 0 signal
(G186)
2 Air flow monitoring (terminal 213 is scanned)
Fault message (F027) in response to 0 signal
P498 Temperature switch: Tripping of alarm or fault message
*
0 No temperature switch connected (terminal 214 is not scanned)
FDS
1 Temperature switch connected (terminal 214 is scanned)
Alarm (A028) in response to 0 signal
(G186)
2 Temperature switch connected (terminal 214 is scanned)
Fault message (F028) in response to 0 signal
11.28 Configuring of torque shell input
P500 Source for torque setpoint for slave drive
*
Selection of the connector to be injected as the torque setpoint for a slave
BDS
drive
(G160) 0 = connector K0000
1 = connector K0001
etc.
P501 Source for additional torque setpoint
*
Selection of connector to be injected as the additional torque setpoint
BDS
0 = connector K0000
(G160) 1 = connector K0001
etc.
SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
Value range No. indices
[Unit] Factory
Steps setting
Type
0 to 3 Ind: 4
1 FS=0
Type: O2
0 to 2 Ind: 4
1 FS=0
Type: O2
0 to 2 Ind: 4
1 FS=0
Type: O2
0 to 2 Ind: 4
1 FS=0
Type: O2
0 to 2 Ind: 4
1 FS=0
Type: O2
All connector Ind: 2
numbers FS=170
1 Type: L2
All connector Ind: 2
numbers FS=0
1 Type: L2
Parameter list
See
Change
(Access /
Status)
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
11-55