Siemens 6RA7086-6KS22 Operating Instructions Manual page 545

05.05
PNU Description
P768 Normalization of analog output 4
P
(G116)
= ∗
y V [ ] x
100
x = Normalization input (corresponds to filtering output)
y = Normalization output (corresponds to output voltage at analog output
with offset = 0)
P769 Offset for analog output 4
(G116)
11.40 Binary outputs
(see also Section 8, Sheet G112)
P770 Control word for binary selectable outputs
*
i001: 0 Binary selectable output at terminal 46 is not inverted
1 Binary selectable output at terminal 46 is inverted
(G112)
i002: 0 Binary selectable output at terminal 48 is not inverted
(G200)
1 Binary selectable output at terminal 48 is inverted
i003: 0 Binary selectable output at terminal 50 is not inverted
1 Binary selectable output at terminal 50 is inverted
i004: 0 Binary selectable output at terminal 52 is not inverted
1 Binary selectable output at terminal 52 is inverted
P771 Source for output value at binary output 1
*
Selection of binector to be injected at binary selectable output, terminal 46
0 = binector B0000
(G112)
1 = binector B0001
(G200)
etc.
P772 Source for output value at binary output 2
*
Selection of binector to be injected at binary selectable output, terminal 48
0 = binector B0000
(G112)
1 = binector B0001
(G200)
etc.
P773 Source for output value at binary output 3
*
Selection of binector to be injected at binary selectable output, terminal 50
0 = binector B0000
(G112)
1 = binector B0001
etc.
P774 Source for output value at binary output 4
*
Selection of binector to be injected at binary selectable output, terminal 52
0 = binector B0000
(G112)
1 = binector B0001
etc.
P775 Delay for output value at binary output 1
The logic level at the binary selectable output changes only if the internal
(G112) signal level remains constant for the set delay period (internal signal level
(G200) changes which do not last as long as this delay period are not switched
through to the output)
P776 Delay for output value at binary output 2
The logic level at the binary selectable output changes only if the internal
(G112) signal level remains constant for the set delay period (internal signal level
(G200) changes which do not last as long as this delay period are not switched
through to the output)
P777 Delay for output value at binary output 3
The logic level at the binary selectable output changes only if the internal
(G112) signal level remains constant for the set delay period (internal signal level
changes which do not last as long as this delay period are not switched
through to the output)
SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
768
%
Value range No. indices
[Unit] Factory
Steps setting
Type
-200.00 to 199.99 Ind: None
[V] FS=10.00
0.01V Type: I2
-10.00 to 10.00 Ind: None
[V] FS=0.00
0.01V Type: I2
0 to 1 Ind: 4
1 FS=0
Type: O2
All binector numbers Ind: None
1 FS=0
Type: L2
All binector numbers Ind: None
1 FS=0
Type: L2
All binector numbers Ind: None
1 FS=0
Type: L2
All binector numbers Ind: None
1 FS=0
Type: L2
0 to 10000 Ind: None
[ms] FS=0
1ms Type: O2
0 to 10000 Ind: None
[ms] FS=0
1ms Type: O2
0 to 10000 Ind: None
[ms] FS=0
1ms Type: O2
Parameter list
See
Change
(Access /
Status)
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
11-81