Siemens 6RA7086-6KS22 Operating Instructions Manual page 620

Parameter list
PNU Description
11.83 Configuration of SCB1 with SCI
U690 Configuration of analog inputs of SCI1
(2690) Definition of type of input signals
Parameter value
(Z150)
(Z151)
0:
1:
2:
Notes:
- Only one signal can be processed per input. Voltage or current signals can
be evaluated.
- Voltage and current signals must be connected to different terminals.
- Only unipolar signals are permitted with settings 1 and 2, i.e. the internal
process quantities are also unipolar.
- When setting 2 is selected, an input current of< 2 mA causes shutdown on
faults (open-circuit monitoring)
- The offset compensation for the analog inputs is set in parameter U692.
i001: Slave 1, analog input 1
i002: Slave 1, analog input 2
i003: Slave 1, analog input 3
i004: Slave 2, analog input 1
i005: Slave 2, analog input 2
i006: Slave 2, analog input 3
U691 Smoothing time constant for analog inputs of SCI1
(2691) Formula: T = 2ms * 2 to the power of U691
i001: Slave 1, analog input 1
i002: Slave 1, analog input 2
(Z150)
i003: Slave 1, analog input 3
(Z151)
i004: Slave 2, analog input 1
i005: Slave 2, analog input 2
i006: Slave 2, analog input 3
U692 Offset compensation for analog inputs of SCI1
(2692) Setting instructions, see Operating Instructions for SCI1
i001: Slave 1, analog input 1
i002: Slave 1, analog input 2
(Z150)
i003: Slave 1, analog input 3
(Z151)
i004: Slave 2, analog input 1
i005: Slave 2, analog input 2
i006: Slave 2, analog input 3
U693 Actual value output via analog outputs of SCI1
(2693) Selection of connectors whose values are to be output (for details, see
Operating Instructions for SCI1)
i001: Slave 1, analog output 1
(Z155)
i002: Slave 1, analog output 2
(Z156)
i003: Slave 1, analog output 3
i004: Slave 2, analog output 1
i005: Slave 2, analog output 2
i006: Slave 2, analog output 3
U694 Gain for analog outputs of SCI1
(2694) Setting instructions, see Operating Instructions for SCI1
i001: Slave 1, analog output 1
i002: Slave 1, analog output 2
(Z155)
i003: Slave 1, analog output 3
(Z156)
i004: Slave 2, analog output 1
i005: Slave 2, analog output 2
i006: Slave 2, analog output 3
11-156
Terminals Terminals
X428/3, 6, 9 X428/5, 8, 11
-10 V ... + 10 V - 20 mA ... + 20 mA
0 V ... + 10 V 0 mA ... + 20 mA
4 mA ... + 20 mA
Value range
[Unit]
Steps
[SW 1.9 and later] 0 to 2
1
[SW 1.9 and later] 0 to 15
1
-20.00 to 20.00
[SW 1.9 and later]
[V]
0.01V
All connector
[SW 1.9 and later]
numbers
1
-320.00 to 320.00
[SW 1.9 and later]
[V]
0.01V
SIMOREG DC Master
05.05
No. indices See
Factory Change
setting (Access /
Type Status)
Ind:6 P052 = 3
FS= 0 P051 =40
Type O2 on-line
Ind:6 P052 = 3
FS= 2 P051 =40
Type O2 on-line
Ind:6 P052 = 3
FS= 0 P051 =40
Type I2 on-line
Ind:6 P052 = 3
FS= 0 P051 =40
Type L2 on-line
Ind:6 P052 = 3
FS= 10.00 P051 =40
Type I2 on-line
SIEMENS AG 6RX1700-0AD76
Operating Instructions