Kenwood NX-5000 Series Common Function Reference page 141

6 SOUND
6.1 Tones that Sound When a User Operates the Transceiver or When the Transceiver Status Is Changed
Function
Not Authorized Tone
No Reply Tone
Call Fail Tone
Call Deny Tone
Lone Worker Tone
Group-registration Invalid
Tone
Call Processing Tone
Network Failure Tone A
Network Failure Tone B
Man-down Pre-alert
(Portable only)
Stationary Pre-alert Tone
(Portable only)
Motion Pre-alert Tone
(Portable only)
Key Fail Alert Tone
Common FUNC (K, F)/Ver 2.20
While sending a Telephone Call in a P25 Trunking system, this tone sounds from the
transceiver when the transceiver receives from the system a response message that service
is disabled (Reason Code: $41).
This tone sounds from the transceiver when the transceiver receives a message from the
system notifying that no response has been received from the receiving transceiver in an
NXDN Trunking system or P25 Trunking system.
This tone sounds from the transceiver when the transceiver receives no message from the
system in an NXDN Trunking system or P25 Trunking system.
P25 Conventional system:
This tone sounds from the transceiver when a Registration Response - Denied is received
while the Rekey Request key is pressed and held with the registration (CAI Data
Registration) unsuccessful.
This tone sounds from the transceiver while the Rekey Request key is pressed and held
with CAI Data Registration denied.
P25 Trunking system:
This tone sounds from the transceiver if the transceiver receives a rejection response
message from the target transceiver when sending an Individual Call.
NXDN Conventional system:
In an Individual Call (Individual Call Acknowledge Request), this tone sounds from the
transceiver if a cancellation notification message is received from the receiving transceiver
while waiting to receive a response from the receiving transceiver.
NXDN Trunking system:
In an Individual Call (Message Trunked (Enhanced)), this tone sounds from the transceiver
if a cancellation notification message is received from the receiving transceiver while waiting
to receive a response from the receiving transceiver.
This tone sounds from the transceiver when the amount of time configured in Lone Worker
Interval elapses after the transceiver enters Lone Worker Mode.
In an NXDN Trunking system, this tone sounds at 30-sec intervals from the transceiver upon
receipt of a response message from the system indicating a failure in Group ID registration.
NXDN Trunking/ P25 Trunking system:
When the transceiver initiates an Individual Call or Group Call by pressing the PTT switch,
this tone sounds from the transceiver while the PTT switch is pressed and held. However,
when sending an Individual Call (Message Trunked (Enhanced)) in an NXDN Trunking
system, the tone from the transceiver continues to sound even if the PTT switch is released.
NXDN Conventional system:
This tone sounds from the transceiver when the transceiver initiates an Individual Call
(Individual Call Acknowledge Request) by pressing the PTT switch. The tone from the
transceiver continues to sound even if the PTT switch is released.
In an NXDN Trunking system, this tone sounds at 5-sec intervals from the transceiver while
the transceiver is in Network Failure Mode.
In an NXDN Trunking system, this tone sounds from the transceiver when the transceiver
exits Network Failure Mode.
After the transceiver is detected to be in a tilted state by using the Man-down Detection
function, this tone sounds from the transceiver when the time configured in Man-down Pre-
alert elapses.
After the transceiver is detected to be in a stationary state by using the Stationary Detection
function, this tone sounds from the transceiver when the time configured in Stationary Pre-
alert elapses.
After the transceiver is detected to be in a vigorously moving state by using the Motion
Detection function, this tone sounds from the transceiver when the time configured in Motion
Pre-alert elapses.
Upon transmission using the Encryption function by means of AES/DES, this tone sounds
from the transceiver if no SCM is installed in the transceiver, or if the SCM is disabled, or if
no encryption key data corresponding to the Multi-key List Number is configured on the
SCM.
Description
CONTENTS
110
INDEX