Kenwood NX-5000 Series Common Function Reference page 250

11 EXTERNAL PORTS
11.2 D-sub 25-pin Connector
Function Name
The TOR or Channel Busy output port is active while the conditions to activate TOR or the
TOR or Channel Busy conditions to activate Channel Busy are satisfied. If conditions to activate the TOR and Channel
Busy are not satisfied, the TOR or Channel Busy output port is inactive.
The output port is active while the transceiver does not accept a remote control request from an
external device. The output port is active while the transceiver is in the following states.
0
Channel Busy
0
The output port is active when a repeater has no available channels in an LTR Trunking system.
System Busy
Otherwise, this port is inactive.
The port output is changed with the state of the AUX A key. An external device connected to the
AUX A
AUX A port can be controlled.
The port output is changed with the state of the AUX B key. An external device connected to the
AUX B
AUX B port can be controlled.
The port output is changed with the state of the AUX C key. An external device connected to the
AUX C
AUX C port can be controlled.
PTT Output The output port is active while the PTT switch is being pressed. Otherwise, this port is inactive.
TXS The output port is active while the transceiver is transmitting. Otherwise, this port is inactive.
The port output changes by linking with the state of the AUX Output ID 1 port to the AUX Output
ID 3 port. External devices connected to each port of AUX Output ID 1 to AUX Output ID 3 can be
controlled.
AUX Output ID 1 to AUX Output ID 3 can be changed to high level or low level by operating the
AUX Output ID 1 to AUX Output ID 3 keys.
If "Off" is configured in State Hold Timer (Active Low):
AUX Output ID 1 to
AUX Output ID 3
If anything other than "Off" is configured in State Hold Timer (Active Low):
Common FUNC (K, F)/Ver 2.20
The output port is active regardless of the configuration in Data Override (AUX Input) while the
transceiver is in the following states:
While the transceiver is transmitting (including while a link is established in an LTR Trunking
0
system)
While the Public Address function is used
0
While System Search is being executed (LTR Trunking)
0
While the transceiver is in Emergency Mode
0
While the transceiver is in Transceiver Password Mode
0
While the transceiver is in the Stun state
0
While the transceiver is in the Radio Inhibit state
0
While the transceiver is on a P25 or NXDN channel
0
While the transceiver is on a DMR channel
0
If Data Override (AUX Input) is disabled, the output port is active while the transceiver is in the
following states:
While Auto Telephone Search is being executed (LTR Trunking)
0
While the transceiver is in Function Mode
0
While an ID is displayed by transmitting and receiving a FleetSync Selcall/ Paging Call, by
0
transmitting and receiving an MDC-1200 Selcall/ Call Alert, by receiving an NXDN Individual
Call/ Group Call, by receiving a DMR Individual Call/ Group Call, or by receiving a P25
Individual Call/ Group Call
While an ID is displayed by transmitting via Caller ID Stack List selection in Stack Mode
0
While the Public Address function is used
0
While the transceiver temporarily migrates to a channel by pressing one of the Direct
0
Channel 1 to Direct Channel 5 keys, Home Channel, or Channel Recall key
Each time one of the AUX Output ID 1 to AUX Output ID 3 keys is pressed, the AUX Output
ID 1 to AUX Output ID 3 ports are toggled from high level to low level or from low level to high
level.
Pressing the AUX Output ID 1 to AUX Output ID 3 keys toggles the AUX Output ID 1 to AUX
Output ID 3 ports to low level.
Description
CONTENTS
219
INDEX