Mitsubishi Electric MELSEC-Q Series User Manual page 253

Number Name
SW0000
Link stop/start direction
SW0002
to
SW0008
SW0011
Reserved station
to
function disable setting
SW0017
Number of resends
SW001A
(REMFR/REMTO)
Response wait timer
SW001B
(REMFR/REMTO)
Sets the station where cyclic transmission is stopped or started.
02H: Specified station
82H: Specified station (Forced link start)
• Stopping/starting of cyclic transmission is performed by System link start (SB0002) or System
link stop (SB0003).
• When Specified station ( 02H or 82H) is selected, the own station is not included.
When setting 02H or 82H by the Link stop/start direction (SW0000), this sets the station No. that
stops or starts cyclic transmission.
0: No direction issued for stop or start
1: Direction issued for stop or start
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
SW0002 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
SW0003 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
SW0004 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
SW0005 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
SW0006 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
SW0007 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97
__ __ __ __ __
SW0008
Specify the slave station for which the reserved station setting is to be temporary
canceled/restored.
0: Not specified
1: Specified
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
SW0011 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
SW0012 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
SW0013 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
SW0014 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
SW0015 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
SW0016 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97
__ __ __ __ __
SW0017
(Conditions)
• For some stations, reserved station setting cannot be temporarily canceled/restored. (Refer to
Section 9.6.)
• Stations higher than the maximum station No. are ignored.
Specifies the number of resends for the REMFR/REMTO instruction.
0: 0 times (default)
Outside the above: Number of times that is set
(Condition)
• This is enabled when Baton pass status (own station) (SB0047) is off.
Specifies the response wait time for the REMFR/REMTO instruction.
0: 10 seconds (default)
Outside the above: Number of seconds that is set
(Condition)
• This is enabled when Baton pass status (own station) (SB0047) is off.
Appendix - 17
Description
__ __ __
120 119 118 117 116 115 114 113
Each number in the table represents station No.
__ __ __
120 119 118 117 116 115 114 113
Each number in the table represents station No.
Appendices