Suzuki sq-416-420-625 Service Manual page 142

DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION
Toe-Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Checks Prior to Adjusting Front Alignment
Toe Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camber and Caster Adjustment
Steering Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front alignment refers to the angular relationship between the front wheels, the front suspension attaching parts
and the ground. Generally, the only adjustment required for front alignment is toe setting.
Camber and caster can't be adjusted. Therefore, should camber or caster be out of specification due to the damage
caused by hazardous road conditions or collision, whether the damage is in body or in suspension should be deter-
mined. If the body is damaged, it should be repaired and if suspension is damaged, it should replaced.
TOE SETTING
Toe is the turning in or out of the front wheels. The purpose of a toe specification is to ensure parallel rolling of the
front wheels (Excessive toe-in or toe-out may increase tire wear).
Amount of toe can be obtained by subtracting "A" front "B" as shown in above figure and therefore is given in mm
(in.).
SECTION 3A
FRONT END ALIGNMENT
CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alignment service data (without load)
Toe-in (Toe-in gauge measurement)
"B" – "A":
Camber angle "C": 0' 8 1D
Caster:
*1. Forward
*2. Body center
1. Center line of wheel
FRONT END ALIGNMENT 3A-1
3A-1
3A-1
3A-2
3A-2
3A-2
3A-2
3A-3
0 8 2 mm (0 8 0.08 in.)
2D40' 8 1D
[A] : Top view
[B] : Front view
3A
3-1