Komatsu PC200-8M0 Shop Manual page 256

SEN06122-00
No. Item
Connected part of boom
9
and boom cylinder
Connected part of boom
10
and arm cylinder
Connected part of boom
11
and arm
Connected part of arm
12
cylinder and arm
Connected part of arm
13
and bucket cylinder
Connected part of link
14
and bucket
Connected part of
15a
bucket cylinder and link
Connected part of link
15b
and link
Connected part of arm
16
and link
Connected part of arm
17
and bucket
4
10-500
Width of boss
Standard
Tolerance
dimension
695
L9-1: Adjust with combination of shims 1.0 mm (1) and 2.0 mm (2)
L9-2: Insert the shim 1.0 mm (1)
(*2)
R9-1: Insert the shim 1.0 mm (1)
R9-2: Insert the shim 1.0 mm (1)
L9-1: Insert the shims 0.8 mm (1) and 1.5 mm (2)
L9-2: Insert the shim 1.5 mm (1)
(*3)
R9-1: Insert the shim 1.5 mm (1)
R9-2: Insert the shim 1.5 mm (1)
96
L10: Insert the shim 1.0 mm (1)
(*2)
R10: Adjust with combination of shims 1.0 mm (1) and 2.0 mm (2)
L10: Insert the shim 1.5 mm (1)
(*3)
R10: Adjust with combination of shims 0.8 mm (1) and 1.5 mm (3)
305.5
L11: Insert the shim 2.0 mm (1)
(*2)
R11: Adjust with either shim 2.0 mm (1) or 2.5 mm (1) or 3.0 mm (1)
L11: Insert the shim 1.5 mm (1)
(*3)
R11: Adjust with combination of shims 0.8 mm (1) and 1.5 mm (2)
106
L12: Insert the shim 1.0 mm (1)
(*2)
R12: Insert the shim 1.0 mm (1)
L12: Insert the shim 1.5 mm (1)
(*3)
R12: –
96
L13: Insert the shim 1.0 mm (1)
(*2)
R13: Adjust with combination of shims 1.0 mm (1) and 2.0 mm (2)
L13: Insert the shim 1.5 mm (1)
(*3)
R13: Adjust with combination of shims 0.8 mm (1) and 1.5 mm (2)
325
L14: –
–
R14: –
96
L15a: –
–
R15a: –
280
R15b: –
(*3)
L15b: Adjust with combination of shims 0.8 mm (1) and 1.5 mm (4)
280
L16: Adjust with combination of shims 0.8 mm (1) and 1.5 mm (3)
(*3)
R16: –
325
L17: –
(*4)
R17: Adjust with combination of shims 0.5 mm (4) and 1.0 mm (12)
Criteria
Width of hinge
Standard
Tolerance
dimension
±2.4 701
±1.2 99.3
0
310
-0.5
±1.2 109.3
±1.2 99.3
±0.5 326.5
±1.2 100.2
0
–
-0.5
0
–
-0.5
0
327.5
-0.5
500 Work equipment
Work equipment
Standard
clearance
+3
2.6 to 11.4
-1 Adjust with shims
so that the clear-
ance is 1.0 mm
(*3), 1.5 mm (*2)
+1.5
2.1 to 6.0
Adjust with shims
0
so that the clear-
ance is 1.0 mm
(*3), 1.5 mm (*2)
+0.5
4.5 to 5.5
0
Adjust with shims
so that the clear-
ance is 1.0 mm or
+1.5
2.1 to 6.0
0
Replace shim
+1.5
2.1 to 6.0
Adjust with shims
0
so that the clear-
ance is 1.0 mm
(*3), 1.5 mm (*2)
±1 0 to 3.0
+0.5 2.5 to 5.9
Adjust with shims
– –
so that the clear-
ance is 1.0 mm or
Adjust with shims
– –
so that the clear-
ance is 1.0 mm or
+2.2 Adjust with shims
2.3 to 5.2
-0.2 so that the clear-
ance is between
0.5 mm and 1.0
PC200, 200LC, 220, 220LC-8M0
Unit: mm
Remedy
or below
or below
below
or below
–
–
below
below
mm