ABB IP Touch 7 Manual page 7

2.21 Application "Internal RTC" ............................................................................................................. 139
2.21.1
2.21.2
2.21.3
2.21.4
2.21.5
2.21.6
2.21.7
2.21.8
2.21.9
2.21.10
2.21.11
2.21.12
2.21.13
2.21.14
2.21.15
2.21.16
2.21.17
2.21.18
2.21.19
2.21.20
2.21.21
2.21.22
2.21.23
2.21.24
2.21.25
2.21.26
2.21.27
2.21.28
2.21.29
2.21.30
2.21.31
2.21.32
2.21.33
2.21.34
2.21.35
2.21.36
2.21.37
2.21.38
2.21.39
2.21.40
2.21.41
2.21.42
2.21.43
2.21.44
2.21.45
2.21.46
2.21.47
2.21.48
2.21.49
2.21.50
2.21.51
Product manual 2CKA001473B5023
General - Device function .......................................................................................................139
General - Control function .......................................................................................................139
General - Operating mode after reset ........................................................................................140
General - Send cyclic "In operation" (min) ..............................................................................141
General - Additional functions/objects .......................................................................................141
General - Delay time for read telegrams after reset [s]............................................................141
Heating control - Control value type ........................................................................................142
Heating control - Heating type .................................................................................................143
Heating control - P-component (x 0.1°C) ................................................................................143
Heating control - I-component (min.) .......................................................................................144
Heating control - Extended settings ........................................................................................144
Basic stage heating ...................................................................................................................144
Basic stage heating - Status object heating ............................................................................144
Basic stage heating - Mode of the control value ......................................................................144
Basic stage heating - Hysteresis (x 0.1°C) ..............................................................................145
Basic stage heating - Control value difference for sending of heating control value ................145
Basic stage heating - Cyclic sending of the control value (min)...............................................145
Basic stage heating - PWM cycle heating (min) ......................................................................146
Basic stage heating - Maximum control value (0 - 255) ...........................................................146
Basic stage heating - Minimum control value for basic load (0 to 255) ....................................146
Settings of basic load - Minimum control value for basic load > 0 ...........................................147
Basic load settings - Basic load active when controller is off ...................................................147
Setpoint settings - Setpoint temperature for heating comfort (°C) ...........................................148
Setpoint settings - Reduction for standby heating (°C) ............................................................148
Setpoint settings - Reduction for ECO heating (°C) ................................................................148
Setpoint settings - Set-point temperature for frost protection (°C) ...........................................149
Setpoint settings - Send current setpoint ................................................................................149
Setpoint settings - Cyclic sending of the current set-point temperature (min) ..........................149
Setpoint adjustment - Maximum manual increase during heating mode (0 - 9°C) ...................149
Setpoint adjustment - Maximum manual reduction during heating mode (0 - 9°C) ..................150
Setpoint adjustment - Resetting of the manual adjustment for receipt of a basic setpoint .......150
Setpoint adjustment - Resetting the manual adjustment for change of operating mode ..........150
Setpoint adjustment - Resetting the manual adjustment via object .........................................151
Setpoint adjustment - Permanent storage of on-site operation ...............................................151
Temperature reading - Inputs of temperature reading .............................................................151
Temperature reading - Inputs of weighted temperature reading .............................................151
Temperature reading - Weighting of internal measurement (0 to 100%) .................................152
Temperature reading - Weighting of external measurement (0 to 100%) ................................152
Temperature reading - Weighting of external measurement 2 (0 to 100%) .............................152
Temperature reading - Cyclic sending of the actual temperature (min) ...................................152
Temperature reading - Difference of value for sending the actual temperature (x 0.1°C) ........153
Temperature reading - Adjustment value for internal temperature measurement (x 0.1°C) ....153
Temperature reading - Monitoring time for temperature reading (0 = no monitoring) (min) .....153
Temperature reading - Control value for fault (0 - 255) ...........................................................154
Alarm functions - Frost alarm temperature for HVAC and RHCC status (°C) ..........................154
Alarm functions - Heat alarm temperature for RHCC status (°C) ............................................154
Control of additional heating stage - Temperature difference to basic stage (x 0.1°C) ............154
Control of additional heating stage - Additional heating type ...................................................155
Control of additional heating stage - P-component (x 0.1°C) ..................................................155
Control of additional heating stage - I-component (min) ..........................................................156
Cooling control - Cooling type .................................................................................................156
Table of contents
│7