Fieldbus Equivalent; Default Values With Different Macros - ABB ACS355 User Manual

176 Actual signals and parameters

Fieldbus equivalent

Example: If 2017 MAX TORQUE 1
system, an integer value of 1000 corresponds to 100.0%. All the read and sent values
are limited to 16 bits (-32768...32767).

Default values with different macros

When application macro is changed (parameter
updates the parameter values to their default values. The table below shows the
parameter default values for different macros. For other parameters, the default
values are the same for all macros (shown in the parameter list starting on page 185).
Index Name/ ABB
Selection STANDARD
9902 APPLIC 1 =
MACRO ABB
STANDARD
1001 EXT1 2 =
COMMANDS
1002 EXT2 0 =
COMMANDS SEL
1003 DIRECTION 3 =
REQUEST
1102 EXT1/EXT2 0 =
SEL
1103 REF1 SELECT 1 =
1106 REF2 SELECT 2 =
1201 CONST 9 =
SPEED SEL
1304 MINIMUM AI2 1.0%
1501 AO1 103
CONTENT SEL
1601 RUN ENABLE 0 =
SEL
2201 ACC/DEC 1/2 5 =
SEL
3201 SUPERV 1 103
PARAM
3401 SIGNAL1 103
PARAM
9904 MOTOR CTRL 3 =
MODE SCALAR:
FREQ
Note: It is possible to control several functions with one input (DI or AI), and there is a
chance of mismatch between these functions. In some cases it is desired to control
several functions with one input.
For example in the ABB standard macro, DI3 and DI4 are set to control constant
speeds. On the other hand, it is possible to select value 6 (DI3U,4D) for parameter
(see page 217) is set from an external control
3-WIRE ALTERNA
TE
2 = 3 =
3-WIRE ALTERNAT
E
DI1,2 4 = 9 =
DI1P,2P,3
NOT 0 = NOT 0 =
SEL SEL
3 = 3 =
REQUEST REQUEST
EXT1 0 = EXT1 0 =
AI1 1 = AI1 1 =
AI2 2 = AI2 2 =
DI3,4 10 = DI4,5 9 =
1.0% 1.0%
102 102
NOT 0 = NOT 0 =
SEL SEL
DI5 0 = NOT 5 =
SEL
102 102
102 102
1 = 1 =
VECTOR: VECTOR:
SPEED SPEED
9902 APPLIC
MOTOR HAND/
POT AUTO
4 = 5 =
MOTOR HAND/AUT
POT O
DI1F,2R 2 = DI1,2 2 =
NOT 0 = NOT 21 =
SEL
3 = 3 =
REQUEST REQUEST
EXT1 0 = EXT1 3 =
AI1 12 = 1 =
DI3U,4D(N
C)
AI2 2 = AI2 2 =
DI3,4 5 = DI5 0 =
SEL
1.0% 20.0%
102 102
NOT 0 = NOT 0 =
SEL SEL
DI5 0 = NOT 0 =
SEL SEL
102 102
102 102
1 = 1 =
VECTOR: VECTOR:
SPEED SPEED
MACRO), the software
PID TORQUE
CONTROL CONTROL
6 = 7 =
PID TORQUE
CONTROL CTRL
DI1,2 1 = DI1 2 =
DI5,4 20 = DI5 2 =
1 = 3 =
FORWARD REQUEST
DI3 2 = DI2 3 =
AI1 1 = AI1 1 =
AI2 19 = 2 =
PID1OUT
NOT 3 = DI3 4 =
20.0% 20.0%
102 102
NOT 4 = DI4 0 =
SEL
NOT 0 = NOT 5 =
SEL
102 102
102 102
1 = 2 =
VECTOR: VECTOR:
SPEED TORQ
DI1,2
DI1,2
DI3
AI1
AI2
DI4
NOT
DI5