Rciu/Rcis Pcb; Rciu/Rcis Installation; Rciu/Rcis Programming - Toshiba Strata DK 280 Installation Manual

An RCIU/RCIS circuit must be available in addition to
each RCOU, RGLU, etc., line that is to receive Caller
ID. When ordered from the factory, the RCIU PCB
comes equipped with four Caller ID circuits; however,
an RCIS piggy-back PCB can be installed onto the
RCIU to provide an additional four Caller ID circuits.
Hence, an installed RCIU/RCIS can provide ,a
maximum of eight Caller ID circuits per cabinet slot.
,
When installing RCIU/RCIS Caller ID circuits, always
install RCIS onto RCIU in order to provide up to eight
circuits. Do not install two RCIU PCBs to provide up to
eight circuits because Program 03 code 81 always
assigns each RCIU slot with eight software Caller ID
circuits.
Each RCIU/RCIS Caller ID circuit has a two-wire
Tip/Ring interface which must be bridge-wired across
its corresponding Ground or Loop Start CO line
Tip/Ring on the Main Distribution Frame (MDF) (see
Figure 7-36 in Chapter 7-Wiring Diagrams). Each
RCILVRCIS modular jack provides interface for two
Caller ID circuits.
4.18.1 RCIU/RClS Installation
RCIU/RCIS PCBs can be installed in any universal
cabinet slot except slot 11 of the base cabinet.
However, if the RSIU is installed in slot 11, the RCIU
cannot be installed in slot 12. It is not necessary to
install the RCIU/RCIS PCBs in slots adjacent to their
associated CO lines or the same cabinet as their
associated CO line.
Install the RCIS onto the RCIU as required (see Figure
4-36 and 4-37). Then install the RCIU/RCIS into the
I
appropriate cabinet slot. The circuit modular jack
numbering and the Tip/Ring cross connect wiring of
RCIU/RCIS to RCOU/RCOS, PCOU, or RGLU is
shown is shown in Figure 7-36 of the DK280
Installation and Maintenance Manual, Chapter 7-
Wiring Diagrams.
4.18.2 RCIU/RClS Programming
Program 03-Program each RCIU or RCIUIRCIS (4
or 8-Caller ID circuit) slot with code 81.
Note:
RCIU/RCIS Caller ID circuits are numbered
automatically in numerical order starting with
the RCIlJ/RCIS installed in the lowest slot
number. Slots with code 81 will increment the
Caller ID circuit numbers by eight circuits
even if RCIS is not installed on RCIU.
Program *50-Assigns CO lines that will receive
Caller ID to an associated RCIU/RCIS Caller ID circuit
number. This assignment is flexible, i.e., any
RCOU/RCOS/PCOU/RGLU Caller ID CO line can be
assigned to any RCIU or RCIS Caller ID circuit
number.
Note:
After assigning CO lines to Caller ID circuits,
turn system power "Ow' for approximately five
seconds and then back "On" or run Program
91-2 to activate Program *50 assignments.
Program *51
W Sets the Caller ID (CLID)/Automatic Dialed
Number Identification (ANI) memory allocation for
the appropriate stations. This memory is used to
save CLIDIANI telephone numbers for calls that
are received but not answered (abandoned calls).
CLID/ANI numbers are not saved in station
memory if they are answered. Stations can be
allocated with memory to save up to 100 numbers
in 1 O-number increments.
The total memory allocated to all stations in a
system is:
n
RCTU C3/D3 = 1000 numbers
n
RCTUBA3/BB3 = 400 numbers
n
RCTUA3 = 200 numbers
Note:
'I
When a CO line rings multiple stations, a
station must be the owner of the Caller ID or
ANI CO line to be able to save abandoned
call (Caller ID and/or ANI) telephone numbers.
(See Program *52.)
Program *52-Assigns stations as owners of Caller
ID CO lines. These stations will store the Caller ID
telephone numbers received on abandoned (not
answered) calls for the lines which they own. Typically
all common CO lines are assigned to one designated
telephone or attendant console and private lines are
assigned to individual private line telephones.
Note:
A station must also be allocated with Caller
ID/AN1 storage memory in Program *51 to
store abandoned call telephone numbers.
Program 39, Code 462~Assigns the Caller-fD/ANI
Lost Call Auto Dial
button to LCD telephones that
store Caller ID and/or ANI abandoned call telephone
4-56
February 1996