Toshiba Strata DK 280 Installation Manual page 386

Digital business telephone system
Hide thumbs Also See for Strata DK 280:
Table of Contents

Advertisement

,
change the Fixed Call Forward destination,
unlike the
other station Call Forwarding
options. This feature
is
valuable for forwarding
to voice mail (VM) devices or
to an attendant.
If Fixed Call Forwarding
is set on a
station, the station will not ring and all calls will forward
immediately.
Program
*36-System
NT Button
Lock Password
Changing
Station Assignment
Attendant
Consoles
and stations
selected
in this
program can change the System Night Transfer Lock
Password. Only one station or console can be allowed
to change the NT Lock password.
System/Tenant
CO
lines can be locked
into the Day, Day2, or Night
ringing
mode only after the NT Lock password
is
entered.
Locking the system into a particular ringing
mode adds security to line call routing which prevents
accidental
or mischievous
changing
of the system
ringing mode.
Any telephone
or an attendant
console can lock the
system into a ringing mode, the telephone
or console
must have an NT Button
and an NT Lock button
assigned
to flexible
buttons
in Program
39 and the
person locking the system must know the Night Lock
password.
Only the station assigned
in this program
can change the code.
Note:
Programs
related
to Program
*36 are:
Program
39 - NT Buttons
and NT Lock
Buttons; Program 74 - system ring mode lock
pass word assignment;
Program * 15 - CO line
Tenant
assignments;
and Program
77-3 -
Tenant Night ring over selected External Page
Zones.
Program
37-CO
and Tie Line Ring Transfer
(Camp-on)
Recall Time
If a busy or ringing station does not answer a call sent
to it via call transfer
(CO lines or over tie lines), the
station originating
the transfer will be recalled after an
amount
of time determined
with this program.
This
time (011 w 999 seconds)
is set independently
for
each originating
station
port. Initialized data sets all
stations
for a 032-second
recall time. Ring Transfer
must first be enabled
for the system with Program
1 O-l, LED 07 ON.
Program
*37-Park
Recall Timing
Each station can have a different duration (from 011 to
9990 seconds)
from the time of parking a call to the
time the parked
party recalls the station.
Initialized
data assigns a park recall time of 032 seconds to all
ports.
Program
38-Digital
and Electronic
Telephone
Keystrip
Type
Four telephone
button
arrangements
are provided
(see the Program 38 System Record Sheet). It is best
to start with one of these four, and then move on to
Program
39, where
individual
buttons
may be
programmed.
Initialized
data
treats
all digital
telephone
ports as 20-button
types with 17 CO line
buttons,
one
Intercom
or [PDN]
button,
one
Do
Not
Disturb
button, and the
Speed
Dial
button.
See the System Record Sheet for electronic telephone
arrangements.
Program
39-Flexible
Button
Assignment
Run Program 38 before entering Program 39. Flexible
feature
buttons
are assigned
to telephones
on a
button-by-button
basis with Program
39. (See the
System Record Sheet for details.)
Programs
40 - 48-Toll
Restriction
All Toll Restriction
program
information
is provided
later in this chapter.
Program
*40-Distributed
Hunt Group
Member
Assignments
Note:
Available with DK280, Release 3.7 and above.
This program
assigns the members
(station primary
[DN] port numbers
and hunting
orders [Ol N 321 of
Distributed
Hunt (DH) groups [900 w 9151). Initialized
data assigns no members for any hunt group. When a
member
of a DH group is added or deleted,
all the
other
members'
hunting
orders
are automatically
rearranged
to a new sequential order.
If Ground/Loop
start CO lines ring DH Group member
telephones,
use Program
81 w 89 to assign
the
selected
CO lines to ring the DH group (900 m 915)
and use *81, *84, and *87 to assign which [PDN] or
[PhDN]
should
ring on the DH Group
member
telephones.
Do not assign DH Group member telephones
to ring in
Program 81-89.
If the CO line that rings the DH Group
(in Program 81 w 89) appears (CO line or Pooled line
button) on the telephones
in the DH Group, l 81 ,.*84,
and l 87 assignments
should not be used. To assign
ANI/DNIS/DID/tie
and Internal calls to ring DH groups,
9-26
February
1996

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents