Toshiba Strata DK 280 Installation Manual page 470

Voice Mail Group/Distributed Hunt Group Programming Example8
DK280
RS232C
I
1
I
Telephones
#200 + '- - - - - -
using voice mail
machine #l
#201 + - - - -
a
- -
008
Telephones
using voice mail
i
#202+---- --
machine #2
#203.+ ----
a
#OlO
DHG2NMGP ,
iv01 1
--
1 1
010
t
RSTU Voice Mail Ports
PROGRAMMING ASSIGNMENTS
Program +32
Program 31
Program *40
000 - 008
001 - 008 VMGl Message Center
002 ... 010
003 - 010
VMG2 Message Center
008 - Button 5 On
VMGl RSTU VM Ports
009 - Button 5 On
OlO- Button 6 On
VMG2 RSTU VM Ports
011 - Button 6 On
850-01 008
VMGl
02 009
DH Group Members
851 -01 010
02 011
VMGl DH Group Members
Voice Mail
Machine #l
Voice Mail
Machine #2
1. A range of ports may be specified by entenn$~O~~n@fl~~~i~~ port
2. A maximum of 120 stations can be assigned to the All Call page group (see Program *30 note 5); AC page is treated as
L
any other page group.
3. This option does not block Attendant Supervised Loop Monitoring.
4. Incoming calls on ground and loop start lines assigned to a pooled line button LED will only flash if they are assigned to
ring the telephone (in Program 81-89). This option is only available with DK280 Release 1, 2, and 3, RCTlJt32 and RCTU
C/D2 processor PCBs and above on which they appear (LED 12 ON). If LED 12 is OFF, the Pooled line LED will flash
when an incoming line call is received - even if the telephone does not ring.
5. If LED 11 is OFF for a port, the DKT or EKT telephone connected to the port will receive two muted rings, three seconds
apart when it receives a call, when the telephone is busy. If LED 11 is ON the telephone will receive repeated muted rings
three seconds apart on an idle [ON], when called during a busy state. If a busy telephone [DN] is called and there are no
idle [DN] buttons available to ring, the telephone will receive two muted rings when the caller activates Busy Override
(BOV) (regardless of LED 11's option). The call will camp-on to the busy [DN]. This option does not apply to standard
telephones which always get two BOV or camp-on tones on/y if enabled in Program *34.
6. With DK280 Release 3 and above, all ports assigned to a Voice Mail Group should also be assigned to a unique
Distributed Hunt Group using Program *40. Each Voice Mail Group must be associated with a unique Distributed Hunt
Group that hunts only to its own Voice Mail Group ports.
7. Handset OCA function on digital telephones only, not electronic or standard telephones.
8. Available with DK280 Release 3.1 and above.
General Notes:
.
Initialized data reads LED 11,12, and 13 ON for all ports; LED 10 is ON forports 000 - 119 only.
l
For Toshiba proprietary integration LEDs 04, 09, 15, 16, 17 and 18 should be ON and for SMDI integration LEDs 04, 09,
16, 17 and 18 should be ON for all RSTU ports connected to the VM machine.
.
l
LED 19 and 20 should be off if the VM machine does not respond properly to transfer recall (B-Tone) signals when using
any type of Voice Mail Interface.
IMPORTANT!
If CO lines direct ring VM ports via Program 8 1 - 89, the data in Programs *81, *84, and *87 must be blank,
1 o-54