Toshiba Strata DK 280 Installation Manual page 410

desirable route number. The most expensive route
is typically programmed to be the least desirable.
A user has three choices upon hearing the
warning tone:
4
b)
c)
Ignore the tone, LCR places the call using the
least desirable route.
Hang up and try later to save money.
Activate the Automatic Call Back feature. The
appropriate line group calls the user back
when a more desirable route number
becomes available.
n OFF: No warning tone sounds.
Program SO-2-LCR Home Area Code
Enter the local area code in the spaces provided on
the record sheet. Initialized data leaves the home area
code blank.
1
LCR matches the area code entered here with the
LCR route plan containing the home area code in
its Area Code Table. (The home area code is later
entered into one of the available LCR route plans
through Program 51). Thus, LCR is informed of
how to handle local calls.
n Typically, systems are configured to have the LCR
route plan containing the home area code as the
same as the local route plan defined in Program
50-5. This is typically programmed by the installer
to be Route Plan Number 1, rather than the
default Plan 16.
Programs SO-31 - 35-LCR Special Codes
Five Special Codes can be entered in spaces provided
next to 31 - 35. The codes can be a maximum of four
digits, and should include items such as 911 for
emergency calls, and 411 or l-41 1 for local
information, etc. Initialized data leaves all codes blank.
n When any of these codes are dialed, LCR is
flagged to treat the call as follows:
q The call will be sent over the local call route plan
specified in Program 50-5.
q ,No additional digits need to be dialed. They are
not necessary. Therefore, the call is put through
immediately.
Program 50-4- LCR Long Distance Information
(LDI) Plan Number
Enter the number of the LCR route plan over which
long distance information calls will be routed.
Typically, long distance information calls are routed
over the local call route defined in Program 50-5. The
RCTUC/D common control unit can support up to 16
plans, and the RCTUA, RCTUBAIBB, and the RCTUB
units can support up to eight.)
n If the long distance information plan is chosen in
Program 50-1, the call is routed as defined by this
table.
n Initialized data assigns Plan 16 to be the LDI route
plan.
Program SO-S- LCR Local Call Plan Number
Of the 16 route plans available for LCR call
processing, one must be defined as the Local Call
Plan, typically route Plan 1. Enter the number of the
plan (1 - 16) over which local calls, operator-
assisted/O+ calls, and special code calls will be routed.
Program SO-6-LCR Dial 0 (Zero) Time-out
Enter the maximum number of seconds LCR waits for
a user to dial additional digits after a 0, before it routes
the call to an operator for assistance. LCR will wait
this number of seconds to receive additional digits that
will indicate charge calls, collect calls or other O+ calls.
n The allowed range is 04 - 10 seconds. Always
enter two digits. Initialized data assigns an LCR
dial zero time-out value of 06 seconds.
9.5.3 Route Plan Overview
Programs 51 - 54 define 16 separate LCR route plans
The RCTUC/D common control unit can support up to
16 route plans, and the RCTUA, RCTUBA/BB, and
RCTUB units can support up to eight. The purpose of
the plan scheme is to provide the system with
directions for routing all possible calls, made by all
possible users at all possible times of day. Sixteen
separate plans provide the customer flexibility enough
to route different area codes and exception office
codes over different line groups.
Initialized data assigns all calls to Plan 16 with the
RCTUCYD common control units (Plan 8 with the
RCTUA, RCTUBIVBB, or RCTUB). Any assignments
made in Programs 51 - 54 for Plans 1 - 15 (Plans 1 -
7 with RCTUB, RCTUBA/BB, or RCTUA) will exempt
the defined call from being made on Route Plan 16
9-50
January 1996