Toshiba Strata DK 280 Installation Manual page 457

Program 20 -
Computer Interface Unit and Data interface Unit Configuration
nmniEiinnnnn-ISpklmai~-sPi;;lnnnni~~~-~~~~-1Spkr/~lWoldl
Select = PDKWPDSU Station Logical Port Number
connected to PDIU-DS or to DKT with PDIU-DI or RPCI-DI (R3).
T LEDs 01 - 06 defines data port type;
LEDs 17 - 20 assigns data port to security
group.
Copy this page if more than three DlUs are in
PDKU/RDSU Port Number11 n r
I I I
I
LED ON. LED OFF
Data Security
CirouD 4
I
Not
included
Data Security
Group 2
Data security
Group 3
Not
included
I---
Not
Included
Data Security
Group I
Not
Included
I 1 I
PDIWRPCI NO PDIWRPCI
01
Connected Connected
PDKUlRDSU Port Number11 fin PDKUlRDSU Port Numbern n r
I'
LED X LED ON LED OFF
20
Data Security Not
Group 4 Included
19
Data Security Not
Group 2 Included
16
Data Security Not
Group 3 Included
17
Data Security Not
Group 1 Included
16
15
14
13
12
11 RPCI-DI RPCI-DI
DNIS Sent DNIS Not Sent
10
09
RPCI-DI
RPCI-Dl
Caller ID /ANI
Caller ID I ANI
Sent
Not Sent
06
07
06
DTR Pulse with' No DTR3
Data Release Pulse
05
04
03
02
01
Auto Pause' No Auto
Behind PBX
Pause
PDIU-DS' PDIU-DIIRPCI-DI
Connected Connected
PDIU-DS to
Modem
PDIU-DS to other
Connection
type DCE or DTE
AT Commands AT Commands
and Result Codes Only
PDIWRPCI NO PDIWRPCI
Connected Connected
DNIS Not Sent
06
DTR Pulse with3
No DTR3
Data Release
Pulse
_i
PDIU-OS to
Modem
Connection
PDIU-DS to othf
type DCE or DTI
DKOl
1. Auto pause will be inserted after a Centrex or PBX access code is dialed by a D/U or RPCI: CO line must be assigned in Program 42-O.
and must have access code assigned in Program 42 (1 - 8). Pause time is determined by Program 12-3. A pause will a/so be inserted
after the CO line access code is dialed (by the D/U) in all cases if LED 05 is turned on.
2. Only turn LED 04 on if a PDIU-DS is connected, if LED 04 is turned on for a telephone port, that telephone cannot be called.
3. LED06 should be OFF for PDIU-DS, if PDIU-DS is connected to a modem for a modem pool application. See Chapter 6-Peripheral
Installation, subsection 6.9.6.
General Notes:
.
Initialized data: LED 77 ON, all others OFF
.
UPC/s and DlUs cannot be connected to PDKUl Circuit 8, but can be connected to all 8 PDKU2 circuits. RPCls and DlUs cannot be
connected to PDKU in all slots (see Chapter l-Configuration-Worksheet 2 PDKU slot assignment table).
0. If a PDIU-DS is connected to a modem, refer to Figure 6-36 and Subsection 6.9.6Modem Setup Recommendations.
l
. If a PC is connected to the RPCI or DIU, the escape sequence of the RPCI or DIU should be set in the PC communication software
"Modem Initialization" character sequence. This will ensure that the escape sequence is restored in case the RCPI Telephone or DIU is
unplugged temporarily.
.
RPCI-DI does not require Program 20 assignments if it is not used in the data switching mode; except for LED 10 and/or LED 11 if ANI,
ON/S, and/or Caller ID must be sent from the RPCI-DI to the PC to which it is connected.
January
1996
1 o-41