Toshiba Strata DK 280 Installation Manual page 363

Program 00, Part 2-RCTU RAM Test
Provided with DK280 R3 and above. This Program
can be used to test the RAM on the DK280 RCTU
processor PCBs. If a RAM test error occurs during this
test, the RCTU causing the error should be replaced.
In the case of two-PCB processors, isolation of a RAM
failure will be indicated on the programming telephone
LCD RCTU "C" or RCTU "D". The RAM test procedure
"RCTU RAM TEST GUIDELINES" is provided on the
Program 00-Part 2 Record Sheet.
CAUTION !
Running each RAM Test will drop all calls and
interrupt telephone service for 15 seconds.
Note:
Running Program 00, Part 2 will not change
or erase any customer data.
Program 01 -Station logical Port Display and/or
Change
Enables you to enter a physical port to display the
associated logical port. You then have the option to
assign a new logical port to the physical port. (To
return ports to their initialized settings, see Programs
90 and 91.)
Program 02-Station Physical Port Display and/or
Change
Enables you to enter a logical port to display the
associated physical port. You then have the option to
assign a new physical port to the logical port. (To
return ports to their initialized settings, see Programs
90 and 91.)
Program 03-Flexible PCB Cabinet and Slot
Assignments
After installing all PCBs and running Program 91-1 or
91-9, the software must be informed with Program 03
as to what type of optioned PCBs are installed. Use
the PCB Code Reference Table on the Program 03
record sheet to determine the proper option code for
each PCB with an option.
When entering an option code for the RCTUA,
RCTUB, RCTUBA, or RCTUC common control unit,
always enter the code representing the number of
DTMF receivers for Slot 00. When entering an option
code for the RCTUD unit, always enter the code
representing the number of DTMF receivers installed
for Slot 01.
The Program 03 System Record Sheet provides
space to record station ports assigned to the station,
tie, and DID line PCBs and line numbers-assigned to
the ground loop start, CO, tie, and DID line PCBs.
When installing RCIU/RCIS, enter the Caller ID circuit
numbers (starting with 1 - 8) in place of the CO line
number. Each RCIUIRCIS slot uses eight Caller ID
circuits. Program 03 should be run for the slot of each
new PCB when installing a new PCB in an existing
installation. This record sheet is the main record for
the hardware configuration of the entire system.
CAUTION !
Running Program 91-9 will erase Program 03
option codes. Running Program 91-I will not.
IMPORTANT!
After the complete entry of Program 03, run
Program 97-2 (R3 and above) or turn the
KSU power supply switch off and wait five
seconds before turning it back on. This will set
in memory all of the configuration data
entered in Program 03.
Program 04--Station logical Port Intercom or
Primary Directory Number [PDN] Assignment
Initialized station numbers are 200 - 439. With
Release 3 and above, Intercom numbers are replaced
with Primary Directory Numbers [PDNs]. Door phone
standard numbering is #151 - #159 and #I161 - #163;
the internal modem (IMDU or RMDS) is #19. Port 039
(RCTUA), 089 (RCTUB and RCTUBA/BB) or 2'49
(RCTUC/D) is the DISA class of service port.
Station intercom or [PDNs] can be changed using
Program 04, but door phone and modem numbering
cannot be changed with Program 04. Only the first
digit of a feature code can be changed by using
Program 05. The system automatically assigns door
phone station numbers if a door phone is specified in
Program 77-l. Station Intercom number or [PDN]
assignment is flexible so that each station can have up
to four assigned digits.
All Strata DK280 telephone and data interface unit
User Guides are written using the standard default
access codes and intercom or [PDNs]. If desired, a
telephone accompanying a DSS console can have an
intercom or [PDN] of 0 or 01, etc., without conflict.
If no assignment is made inProgram 04, the system,
upon powering up will automatically assign eight
January 1996
9-3