NEC SL2100 Features And Specifications Manual page 637

ISSUE 1.0
Program Program Name
No.
20-03-04 System Options for Single Line Telephones - Di-
al Sending Start Time for SLT or ARS
80-03-01 DTMF Tone Receiver Setup - Detect Level
14-01-24 Basic Trunk Data Setup - Trunk-to-Trunk Outgo-
ing Caller ID through Mode
21-12-01 ISDN Calling Party Number Setup for Trunks -
Calling Party Number Data
21-13-01 ISDN Calling Party Number Setup for Extensions
- Calling Party Number Data
80-01-01 Service Tone Setup - Tone 54, Progress Tone
80-01-01 Service Tone Setup - Repeat Count
80-03-03 DTMF Tone Receiver Setup - Min. Detect Level
11-10 Service Code Setup (for System Administrator)
11-11 Service Code Setup (for Setup/Entry Operation)
11-12 Service Code Setup (for Service Access)
15-07-01 Programmable Function Keys
20-09-02 Class of Service Options (Incoming Call Service)
- Caller ID Display
22-11-01 DID Translation Table - Received Number
22-11-02 DID Translation Table - Target Number
Features and Specifications Manual
Input Data
0 ~ 64800 seconds
0 = 0 dBm ~ - 25 dBm
1 = - 5 dBm ~ - 30 dBm
2 = - 10 dBm ~ - 35 dBm
3 = - 15 dBm ~ - 40 dBm
4 = - 20 dBm ~ - 45 dBm
5 = - 25 dBm ~ - 50 dBm
6 = - 30 dBm ~ - 55 dBm
0 = Disable (Caller ID not forwar-
ded out.)
1 = Enable (Caller ID is forwar-
ded out.)
Maximum of 16 digits (0 ~ 9, ,
*
#)
Most Telco's will only accept 10
digits.
Maximum of 16 digits (0 ~ 9, ,
*
#)
Most Telco's will only accept 10
digits.
0 ~ 255 (0 = Endless)
0 ~ 15
DTMF Tone 0 = - 10 dBm (0) to -
25 dBm (15)
DTMF Tone 1 = - 15 dBm (0) to -
30 dBm (15)
DTMF Tone 2 = - 20 dBm (0) to -
35 dBm (15)
DTMF Tone 3 = - 25 dBm (0) to -
40 dBm (15)
DTMF Tone 4 = - 30 dBm (0) to -
45 dBm (15)
DTMF Tone 5 = - 35 dBm (0) to -
50 dBm (15)
DTMF Tone 6 = - 40 dBm (0) to -
55 dBm (15)
-
-
-
Code 34 = Barge-In
0 = Off
1 = On
Maximum eight digits
(0 ~ 9, , #, @)
*
Maximum 36 digits
(0 ~ 9, , #, @)
*
SL2100
Default
1
Refer to the Program-
ming Manual for the
default values.
0
M
No Setting
No Setting
Refer to the Program-
ming Manual for the
default values.
Refer to the Program-
ming Manual for the
default values.
Refer to the Program-
ming Manual for the
default values.
Refer to Programming
Manual.
Refer to Programming
Manual.
Refer to Programming
Manual.
Refer to the program-
ming manual for the
default values and for
all other available op-
tions in this command.
COS 01 ~ 15 = 1
Refer to Programming
Manual.
Refer to Programming
Manual.
1-623