NEC UNIVERGE SV9100 Manual page 178

178
DNS Source Port – This is the source port number of the customer's (or ISP's) DNS server.
17)
Register Sub Mode - Prevents an invalid INVITE message. If the register information that SV9100 send to
SIP server and the Invite information that SV9100 receives are different, SV9100 sends "404 Not Found"
Message. (PRG10-29-16)
Call Forward Moved Temporarily Support – When enabled a 302 Moved Temporarily response is sent to
the configured SIP server for external call forward destinations. Requires support by the ITSP to be used.
(PRG84-14-17)
Keep Alive By Option Message – This item will enable or disable the SIP OPTION keep alive function for
checking a SIP server's availability.
Keep Alive By Option Interval Timer – This item sets the interval between receiving a 200 OK response of
an OPTION message to sending the next OPTION message. Default value is 180 seconds (3 minutes).
PRG84-14-18)
Keep Alive By Option Fail Limit – Failure Limit before PBX SIP trunks to destination server are unavailable
(busy). (PRG84-14-19)
Option Keep Alive User ID – This parameter is set in request URI SIP URL of OPTION message.
For example sip:ping@xyzcustomer.com.
Primary Authentication Information
Easy Edit – Advanced Items/VoIP/SIP Networking/Profile x/SIP Profile x - Carrier Mode (Domain Name)/
SIP Profile x - Primary Authentication Information
Registration – This command enabled registration of the user account details with the SIP server. This
should be Enabled for each valid account.
User ID– This is the Username (or User ID) that is supplied by the ITSP. It is part of the authentication
details. This is usually the same as the Username.
Username – This is the Username (or User ID) that is supplied by the ITSP. It is part of the authentication
details. (PRG10-36-03)
Password – This is the password that is supplied by the ITSP. It is part of the authentication details.
(PRG10-36-04)
CODEC Settings
Easy Edit - Advanced Items/VoIP/SIP Networking/Profile x/SIP Profile x - Trunk General Settings/SIP Profile
x - CODEC Settings
Audio Capability Priority – This is the preferred codec for the SIP Trunk call. It is possible that this codec is
not used depending on the settings of the ITSP.
DTMF Settings
Easy Edit - Advanced Items/VoIP/SIP Networking/Profile x/SIP Profile x - Trunk General Settings/SIP Profile
x - DTMF Settings
DTMF Payload Number – This value is used when DTMF Relay is enabled. The ITSP and the SV9100 must
have equal values. If this is not the case, a common equal value will be negotiated.
DTMF Relay Mode – This item is to enable or disable DTMF Relay. To use DTMF Relay set to RFC2833.
(PRG84-34-01)
E.164 Numbering
Easy Edit - Advanced Items/VoIP/SIP Networking/Profile x/SIP Profile x - Trunk General Settings/SIP Profile
x - E.164 Numb er Formatting/SIP Profile x - E.164 Numb er Format Settings
Incoming/Outgoing SIP Trunk for E.164 - Defines the settings for support of E.164 number formatting
when required for specified SIP carriers.
Enabled – When an outgoing call is made and the Country Code in 10-02-01 is empty. A + is added to the beginning
of the Request-URI, To, and From header fields in SIP message. If 10-02-01 is configured with a Country Code then a
+ and also the Country Code are added to the beginning of the Request-URI, To, and From fields.
International Access M ode - When an outgoing call is made and the digits from the beginning of the Calling Party
Number/Called Party Number are the same as the International Access Code in 10-02-02 then deletes the International
Access Code from 10-02-02 and replaces it with a +.
(PRG10-29-19)
(PRG84-14-20)
(PRG10-36-01)
(PRG10-36-02)
(PRG84-13-28)
(PRG84-14-13)
(PRG10-29-
(PRG84-34-02)