Hitachi GR2000 Series Configuration Commands page 397

Table 5-3
Can not delete vc configuration with QoS
interface configuration.
Can not delete vp configuration with vc
configuration.
Can not set adtf.
Can not set bod.
Can not set bri topology on priisdn.
Can not set call reference length on priisdn.
Can not set cdf.
Can not set dch line.
Can not set frtt.
Can not set icr.
Can not set line.
Can not set mbs.
Can not set mcr.
Can not set multiple timeslot.
Can not set pcr.
Can not set priority.
Can not set priority3 pcr.
Can not set rdf.
Can not set rif.
Can not set scr.
Can not set tbe.
Can not set threshold clp0.
Can not set threshold clp1.
Can not set threshold priority1 hi.
Can not set threshold priority1 low.
Can not set threshold priority2 hi.
Can not set threshold priority2 low.
Can not set threshold priority3 hi.
Can not set threshold priority3 low.
Can not set threshold priority4 hi.
Can not set threshold priority4 low.
Can not set timeslot.
Can not set tunnel interface.
Can not set vlan
Can not support vlan.
Connect type is not point.
GR2K-GA-0014
Ver. 07-02
Network Interface Error Messages (continued)
Qos interface information present. Delete Qos interface information;
delete VC information.
VC information present. Delete VC information; delete VP
information.
Can not set adtf. Confirm the traffic type.
BOD is set on the POS line. You are not permitted to set BOD for the
POS line.
The interface type cannot be set to priisdn.
The call number length cannot be set to priisdn.
Can not set cdf. Confirm the traffic type.
Can not set dch line. When own telephone number is undefined on
Priisdn line, Dch line cannot be set.
Can not set frtt. Confirm the traffic type.
Can not set icr. Confirm the traffic type.
Can not set line. To set an APS line, set an OC line in the same NIF.
Can not set mbs. Confirm the traffic type.
Can not set mcr. Confirm the traffic type.
Multiple timeslots cannot be set. Multiple timeslots are not supported.
Can not set pcr. Confirm the traffic type.
Can not set priority. Confirm the traffic type.
Can not set priority3 pcr. Confirm the traffic type.
Can not set rdf. Confirm the traffic type.
Can not set rif. Confirm the traffic type.
Can not set scr. Confirm the traffic type.
Can not set tbe. Confirm the traffic type.
Can not set threshold clp0. Confirm the traffic type.
Can not set threshold clp1. Confirm the traffic type.
Can not set threshold priority1 hi. "Confirm the traffic type" cannot be
set.
Can not set threshold priority1 hi. "Confirm the traffic type" cannot be
set.
Can not set threshold priority2 hi. "Confirm the traffic type" cannot be
set.
Can not set threshold priority2 hi. "Confirm the traffic type" cannot be
set.
Can not set threshold priority3 hi. "Confirm the traffic type" cannot be
set.
Can not set threshold priority3 hi. "Confirm the traffic type" cannot be
set.
Can not set threshold priority4 hi. "Confirm the traffic type" cannot be
set.
Can not set priority3 pcr. "Confirm the traffic type" cannot be set.
Can not set timeslot. Recheck the line type to set the time slot.
Can not set tunnel interface. Confirm the interface setting number
per RP. If an RP set with 256 interfaces is present, the tunnel
interface cannot be set.Change the configuration definition so that
the number of interfaces set in the applicable RP is less than 255
and then re-actuate the device.
A VLAN line cannot be set. Set it to RP and NIF compatible with
Tag-VLAN when setting a VLAN line.
Not compatible with a VLAN line. Use RP and NIF compatible with
Tag-VLAN when using a VLAN line.
Connect type is not point. Specify point to the IP type.
Configuration Error Messages
5-7