Hitachi GR2000 Series Configuration Commands page 424

Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
Table 5-5
export: route-filter not found at <Value>
export: Set-attribute "<Name>" cannot be
specified
export: Set-attribute not found at <Value>
export: syntax error
export: tag option of route-filter must not be
define for { bgp | bgp4+ | rip | ripng }
export: type option of route-filter must not be
define for { bgp | bgp4+ | rip | ripng }
hosts: address should not be v4-compat
hosts: address should not be v4-mapped
hosts: last 64bit of IPv6 host address should
not be all-zero
hosts: linklocal address should be followed by
% (IPv6 interface name)
import: address not IPv6
import: address should not be::
import: address should not be v4-compat
import: address should not be v4-mapped
import: Attribute-filter " <Name>" cannot be
specified
import: Attribute-filter not found at <Value>
import: attribute-list name "<Name>" longer
than 15 characters
import: {bgp|bgp4+} attribute option of
route-filter must not be define for
{rip|ripng|ospf_ase|ospf6_ase}
import: duplicate AS path pattern in list
import: duplicate autonomous-system in list at
<As>
import: duplicate entry at <Address> mask
<Mask> [exact | refine]
5-34
Routing Protocol Error Messages (continued)
The specified ID is not defined. Specify the defined ID
<Value>: specified ID
Filter information inherent to IPv4 is defined in IPv6. Do not specify
the filter information inherent to IPv4.
<Name>: Specified identifier
The specified ID number is not defined, or cannot be found. Specify
the defined ID number
<Value>: Specified ID number
Syntax error
The tag option of a router filter is defined for an export filter or BGP/
BGP4+/RIP/RIPng protocol. Do not specify a tag option.
The type option for the route filter is defined against the BGP/BGP4+/
RIP/RIPng protocol. Do not specify the type option.
An IPv4-compatible address is specified in an address. Specify
addresses other than the IPv4-compatible address.
An IPv4 mapped address is specified in an address. Specify
addresses other than the IPv4 mapped address.
The lower-order 64 bits of the host address are all specified with
zero. Specify the address so that all of the lower-order 64 bits are not
zero.
An interface name is not specified in the specified link local address.
Specify an interface name with the percent (%) interposed when
specifying a link local address.
Addresses other than an IPv6 prefix are specified. Specify the IPv6
prefix.
Default address is specified in the address. Specify addresses other
than the local host address.
An IPv4-compatible address is specified in an address. Specify
addresses other than the IPv4-compatible address.
An IPv4 mapped address is specified in an address. Specify
addresses other than the IPv4 mapped address.
Filter information inherent to IPv4 is defined in IPv6. Do not specify
the filter information inherent to IPv4.
<Name>: Specified identifier
The specified ID number cannot be found. Specify the defined ID
number
<Value>: Specified ID number
The specified ID exceeds 15 characters. Specify ID by 15 or less
characters.
<Name>: Specified ID
The BGP/BGP4+ attribute option for the route filter is defined against
the RIP/RIPng/OSPFASE/OSPF6ASE protocol. Do not specify the
BGP/BGP4+ attribute option.
In the import definition, an AS path pattern is duplicated. Use a
unique AS path pattern.
In the import definition, an AS number is duplicated. Use a unique AS
number.
<As>: Specified AS number
In the import definition, a network range is duplicated. Specify a
unique network range.
import <Address>: Specified Address
<Mask>: Specified Mask
GR2K-GA-0014
Ver. 07-02