Hitachi GR2000 Series Configuration Commands page 456

Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
Table 5-8
Can not set max_rate because
replace_user_priority is already defined.
Can not set penalty_tos or penalty_dscp
because upc or min_rate not specified.
Can not set max_rate_burst because
max_rate not specified.
Can not set min_rate because min_rate is
bigger than max_rate.
Can not set min_rate because
replace_user_priority is already defined.
Can not set min_rate because upc is already
defined.
Can not set max_rate because upc is already
defined.
Can not set min_rate_burst because min_rate
not specified.
Can not set penalty_discard because
replace_exp is already defined.
Can not set penalty_discard because
replace_tos or replace_dscp is already
defined.
Can not set penalty_discard because
replace_tos or replace_dscp or tos_map or
dscp_map or replace_exp is already defined.
Can not set penalty_discard because
replace_user_priority is already defined.
Can not set penalty_discard because
tos_map or dscp_map is already defined.
Can not set penalty_discard because upc or
min_rate not specified.
Can not set penalty_drop because
replace_exp is already defined.
5-66
Flow Information Error Messages (continued)
It is not possible to set the maximum bandwidth limitation because
the VLAN priority rewrite value is defined. Delete the VLAN priority
rewrite value in order to set the maximum bandwidth limitation.
The maximum band restriction cannot be set because the band
setting has been defined. To set the Max_rate, delete the band
setting.
The maximum band restriction burst size cannot be set because the
maximum band restriction has not been defined. To set the
maximum band restriction burst size, set the maximum band
restriction.
The minimum band assurance cannot be set because the minimum
band assurance value is bigger than that of the maximum band
restriction. To set the minimum band assurance, specify a value
smaller than the maximum band restriction.
It is not possible to set the minimum bandwidth limitation because the
VLAN priority rewrite value is defined. Delete the VLAN priority
rewrite value in order to set the minimum bandwidth limitation.
The minimum band assurance cannot be set because the band
setting has been defined. To set the Min_rate, delete the band
setting.
The maximum band assurance cannot be set because the band
setting has been defined. To set the Max_rate, delete the band
setting.
The minimum band assurance burst size cannot be set because the
minimum band assurance has not been defined. To set the minimum
band assurance burst size, set the minimum band assurance.
Contract band breaching queuing priority cannot be set because the
exp field rewriting value has been defined. To set the contract band
breaching queuing priority, delete the exp field rewriting value.
Contract band breaching queuing priority cannot be set because the
tos or dscp rewriting value has been defined. To set the contract
band breaching queuing priority, delete the tos or dscp rewriting
value.
Contract band breaching queuing priority cannot be set because the
tos or dscp rewriting value or tos_map or dscp_map, exp field
rewriting value has been defined.
To set the contract band breaching queuing priority, delete the tos or
dscp rewriting value, or tos_map or dscp_map, exp field rewriting
value.
It is not possible to set queuing priority at the time of contract
bandwidth violation because the VLAN priority rewrite value is
defined. Delete the VLAN priority rewrite value in order to set
queuing priority at the time of contract bandwidth violation.
Contract band breaching queuing priority cannot be set because
tos_map or dscp_map has been defined. To set the contract band
breaching queuing priority, delete tos_map or dscp_map. Contract
band breaching queuing priority cannot be set because the tos_map
or dscp_map has been defined. To set the contract band breaching
queuing priority, delete the tos_map or dscp_map.
The contract band breaching queuing priority cannot be set because
the band setting or the minimum band assurance has not been
defined. To set the contract band breaching queuing priority, set the
band setting or the minimum band assurance.
Contract band breaching packet discard cannot be set because the
exp field rewriting value has been defined. To set the contract band
breaching packet discard, delete the exp field rewriting value.
GR2K-GA-0014
Ver. 07-02