Hitachi GR2000 Series Configuration Commands page 401

Table 5-3
Relations between local management and
inverse arp(dlci).
Relations between mcr and icr are
inconsistent.
Relations between mcr and pcr are
inconsistent.
Relations between mcr, pcr and priority4 pcr
are inconsistent.
Relations between overload link add threshold
and overload link drop threshold are
inconsistent.
Relations between overload measuring period
and overload link add threshold and overload
link drop threshold are inconsistent.
Relations between pcr and icr are
inconsistent.
Relations between pcr and mcr are
inconsistent.
Relations between phone number and
interface id are inconsistent.
Relations between priority4 pcr and pcr are
inconsistent.
Relations between scr and pcr are
inconsistent.
Relations between service category pattern,
traffic mcr and traffic pcr are inconsistent.
Relations between service category pattern
and traffic pcr are inconsistent.
Relations between service category pattern
and traffic type are inconsistent.
Relations between service category pattern
and vp shaping number are inconsistent.
Relations between share and vp alarm are
inconsistent.
Relations between threshold clp1 and
threshold clp0 are inconsistent.
Relations between threshold priority1 hi and
threshold priority1 low are inconsistent.
Relations between threshold priority2 hi and
threshold priority2 low are inconsistent.
Relations between threshold priority3 hi and
threshold priority3 low are inconsistent.
Relations between threshold priority4 hi and
threshold priority4 low are inconsistent.
Relations between timeslot number and width
are inconsistent.
Relations between total of vc and vp shaping
number are inconsistent.
GR2K-GA-0014
Ver. 07-02
Network Interface Error Messages (continued)
Although the DLCI InARP address solving execution switch is on,
PVC status check protocol is "no."Set the PVC status check protocol
to q933.
Relations between mcr and icr are inconsistent. Set to MCR =< ICR.
Relations between mcr and pcr are inconsistent. Set to MCR =<
PCR.
Relations between mcr, pcr and priority4 pcr are inconsistent.
Set the correct value.
Relations between overload link add threshold and overload link drop
threshold are inconsistent. Set overload start line usage ratio larger
than overload stop line usage ratio.
Relations between overload measuring period and overload link add
threshold and overload link drop threshold are inconsistent.
When overload measurement interval is other than no, set overload
start line usage ratio and overload stop line usage ratio.
Relations between pcr and icr are inconsistent. Set to ICR =< PCR.
Relations between pcr and mcr are inconsistent. Set to MCR =<
PCR.
The relationship between the local phone number, sub-address and
the interface ID. Recheck the value to be set.
Relations between priority4 pcr and pcr are inconsistent. Set the
correct value.
Relations between scr and pcr are inconsistent. Set to SCR =< PCR.
Relations between service category pattern, traffic mcr and traffic pcr
are inconsistent. Set the correct value.
Relations between service category pattern and traffic pcr are
inconsistent. Set the correct value.
Relations between service category pattern and traffic are
inconsistent. Specify the service category pattern traffic type
appropriate for the traffic type.
Relations between service category pattern and vp shaping number
are inconsistent. Specify the maximum VP count of VP shaper
appropriate for the service category pattern.
Relations between share of DLCI/VC group and vp alarm are
inconsistent. Set to share = VP alarm.
Relations between threshold clp1 and threshold clp0 are
inconsistent. Set to threshold clp1 =< CLP0.
Relations between threshold priority1 hi and threshold priority1 low
are inconsistent. Set the correct value.
Relations between threshold priority2 hi and threshold priority2 low
are inconsistent. Set the correct value.
Relations between threshold priority3 hi and threshold priority3 low
are inconsistent. Set the correct value.
Relations between threshold priority4 hi and threshold priority4 low
are inconsistent. Set the correct value.
The (timeslot number, timeslot width) value exceeds other timeslot
number. Correct the (timeslot number, timeslot width) value so the
value does not exceed other timeslot number.
Relations between total of vc and vp shaping number are
inconsistent. Set the correct value.
Configuration Error Messages
5-11