Hitachi GR2000 Series Configuration Commands page 447

Table 5-6
multicast: invalid inet mask bits value at
<Masklen> not in range 4 to 32
multicast: mask length out of range from 4 to
32
multicast: mask not contiguous
multicast: Non-masked bits not zero for
<Group address> / <Masklen>
multicast: Non-masked bits not zero for
<Group address> mask <Mask>
multicast: Non-masked bits not zero for
<Group address> masklen <Masklen>
multicast: octet or hex string too long to be an
IP address
multicast:ssm-join is not supported in
DVMRP, IGMP, DVMRPTUNEL.
multicast:The combination total of GROUP
and SOURCE exceeded the maximum
permitted
multicast:join and staticjoin are not supported
in PIN-SM
multicast: the parameter must be a group
address (class D)
multicast: this address is not supported
<Group address>
multicast:this source address is not supported
<Source address>
PIM and DVMRP can not be set up
simultaneously.
PIM-SM and multicast can not be set up
simultaneously.
pim: can not check configuration, please try
again
pim: can not set candidate-bsr on this router
which is not configured to router
local_address
pim: can not set candidate-rp on this router
which is not configured to router
local_address
GR2K-GA-0014
Ver. 07-02
Multicast Router Control Information Error Messages (continued)
The specified mask length in multicast definition is invalid. Specify
within the range of 4 to 32.
<Masklen>: Specified mask length.
The specified mask pattern in multicast definition is invalid.
Specify mask pattern with length of 4 to 32.
The specified mask in multicast definition is not contiguous with bit 1.
Specify the mask that bit 1 is contiguous.
1 is set to non-masked bits of address for masklen specification in
multicast definition. Specify 0 to non-masked bits.
<Group address>: Specified multicast group address.
<Masklen>: Specified mask length.
1 is set to non-masked bits of address for mask specification in
multicast definition. Specify 0 to non-masked bits.
<Group address>: Specified multicast group address.
<Mask>: Specified mask.
1 is set to non-masked bits of address for masklen specification in
multicast definition. Specify 0 to non-masked bits.
<Group address>: Specified multicast group address.
<Masklen>: Specified mask length.
The specified IP address format is invalid.
Specify in the correct dot format.
The "ssm-join" command is defined when using DVMRP, IGMP and
DVMRPTUNEL.
The sum total of groups and sources defined by "ssm-join" exceeds
the allowable limit. Set the sum total of groups and sources to a
maximum of 256.
"join" and "staticjoin" are not supported with PIM-SM.
The group address specified in multicast definition is invalid.
Specify the group address by IP address of class D.
The specified group address in multicast definition is not supported.
Specify the group address by IP address of class D.
<Group address>: Specified multicast group address.
The range for specifying local addresses specified by "ssm-join" is
invalid. Specify IP addresses of classes A - C.
<Source address>: local address specified by the "ssm-join"
command
The PIM and the DVMRP cannot be set simultaneously. Define only
either one of the PIM information (pim) or the DVMRP information
(igmp, dvmrp, dvmrptunnel).
PIM-SM does not support multicast settings.
The configuration definition cannot be checked because actuation of
the multicast routing program has not been completed. Try it again
after some time.
Unless the device address is defined, there is no setting BSR
candidates. First set the device address.
Unless the device address is defined, there is no setting rendezvous
point candidates. First set the device address.
Configuration Error Messages
5-57