Hitachi GR2000 Series Configuration Commands page 411

Table 5-5
aggregate: linklocal address should be
followed by % (IPv6 interface name)
aggregate: low end of range <Mask1> shorter
than prefix mask <Mask2>
aggregate: low end of range (<Value1> bits) is
greater than high end (<Value2> bits)
aggregate: mask not contiguous
aggregate: Non-masked bits not zero for
<Address> mask <Mask>
aggregate: Non-masked bits not zero for
<Address> masklen <Masklen>
aggregate: not IPv6 prefix.
aggregate: out of range.
aggregate: syntax error
attribute-list: attribute-list name "<Name>"
longer than 15 characters
attribute-list: duplicate Attribute-filter at
<Value>
attribute-list: duplicate extended community.
attribute-list: duplicate Set-attribute at
<Value>
attribute-list: error resolving' <Host Name>':
Unknown host.
attribute-list: invalid as_count value at
<Value> not in range 1 to 25
attribute-list: invalid attribute-list number value
at <Value> not in range 1 to 65535
attribute-list: invalid autonomous system
number value at <Value> not in range 1 to
65534
attribute-list: invalid autonomous system value
at <Value> not in range 1 to 65534
attribute-list: invalid { BGP | BGP4+ } metric
offset value at <Metric> not in range 1 to
4294967295
GR2K-GA-0014
Ver. 07-02
Routing Protocol Error Messages (continued)
An interface name is not specified in the specified link local address.
Specify an interface name with the percent (%) interposed when
specifying a link local address.
In the between specification, lower limit value of the mask range is
overlapped with specified mask. Specify the value so that mask
range does not overlap with specified mask.
<Mask1>: Lower limit value of the specified mask range.
<Mask2>: Specified mask.
In the between specification, lower limit value of the mask range is
greater than upper limit value. Reduce lower limit value of the mask
range to less than upper limit value.
<Value1>: Lower limit value of the mask range
<Value2>: Upper limit value of the mask range
Bit 1 of specified mask does not continue. Use a mask where bit 1
continues.
At mask, 1 is set to non-masked bit of specified address. Set
non-masked bit 0.
<Address>: Specified Address
<Mask>: Specified Mask.
t masklen, 1 is set to non-masked bit of specified address. Set
non-masked bit 0.
<Address>: Specified address
<Masklen>: Specified Mask length
Addresses other than an IPv6 prefix are specified. Specify IPv6
prefix.
Input
Syntax error
The specified ID exceeds 15 characters. Specify ID by 15 or less
characters.
<Name>: Specified ID
The specified ID number has been already registered. Specify the
other ID number.
<Value>: ID number.
The extended community is duplicated for definition. Do not duplicate
the extended community for definition.
The specified ID number has been already registered. Specify the
other ID number
<Value>: ID number
The specified host name is not found. Specify the defined host name.
<Host Name>: Specified host name
The specified ascount value is invalid. Specify within the range of 1
to 25.
<Value>: Specified ascount value.
The specified ID number is invalid. Specify within the range of 1 to
65535.
<Value>: Specified ID number.
The AS number is invalid in the extended community. Specify within
the range of 1 to 65534.
<Value>: Specified As value.
The AS number is invalid. Specify within the range of 1 to 65534.
<Value>: Specified As value.
The range for specifying MED offset values is invalid. Specify within
the range of 1 - 4294967295.
<Metric>: Specified MED offset value
syntax
command
Configuration Error Messages
5-21