Mitsubishi Electric 800 Series Instruction Manual page 278

Monitor item Increment
and unit
Option output —
*9
terminal status
Option input —
terminal status 1
(for
*9
communication)
Option input —
terminal status 2
(for
*9
communication)
Option output —
terminal status 1
(for
*9
communication)
Motor thermal load 0.1%
factor
Inverter thermal 0.1%
load factor
PTC thermistor 0.01 kΩ
resistance
PID measured 0.1%
value 2
Emergency drive 1
*7
status
PID input pressure 0.1%
value
32-bit cumulative 1 kWh
power (lower 16
bits)
32-bit cumulative 1 kWh
power (upper 16
bits)
32-bit cumulative 0.01 kWh/
power (lower 16
*6
0.1 kWh
bits)
32-bit cumulative 0.01 kWh/
power (upper 16
*6
0.1 kWh
bits)
BACnet reception 1
status
BACnet token 1
pass counter
BACnet valid 1
APDU counter
Pr. setting RS-485
*17 —
57
—
*12
H3A
—
*13
H3B
—
*14
H3C
61 H3D
62 H3E
64 H40
67 H43
68 H44
69 H45
— H4D
— H4E
— H4F
— H50
81 H51
82 H52
83 H53
MODBUS Negative
RTU indication
*1
(-)
— Displays output terminal ON/OFF
state of the digital output option (FR-
A8AY) and the relay output option
(FR-A8AR) on the DU. (Refer to the
instruction manual of the operation
panel.)
Input terminal X0 to X15 ON/OFF
*12
40258
state of the digital input option (FR-
A8AX) can be monitored via RS-485
communication and the
communication option.
Input terminal DY ON/OFF state of
*13
40259
the digital input option (FR-A8AX)
can be monitored via RS-485
communication and the
communication option.
Output terminal ON/OFF state of the
*14
40260
digital output option (FR-A8AY) and
relay output option (FR-A8AR) can
be monitored via RS-485
communication and the
communication option.
40261 Displays the accumulated heat value
of the motor thermal O/L relay.
The motor overload trip (E.THM)
occurs at 100%.
40262 Displays the accumulated heat value
of the inverter thermal O/L relay.
The inverter overload trip (E.THT)
occurs at 100%.
40264 Displays the PTC thermistor
resistance when Pr.561 PTC
thermistor protection level ≠ 9999
(voltage monitor when Pr.561 =
9999).
40267 Displays PID measured value even if
PID control operating conditions are
not satisfied while the PID control is
enabled (Pr.128 ≠ "0"). (Refer to
page
40268 Displays the emergency drive status
(Refer to
40269 Displays the input pressure value of
the PID input pressure control
function.
40277 Displays the 32-bit cumulative power
value in multiplies of 16 bits.
Monitoring can be performed via RS-
485 communication and
40278
communication options. (To find the
monitor codes for each
communication option, refer to the
40279
Instruction Manual of each
communication option.)
40280
40281 Displays the BACnet reception
status.
40282 Displays the count of received token.
40283 Displays the count of valid APDU
detection.
5.8 (M) Monitor display and monitor output signal
Description
410)
page 245)
277
5. PARAMETERS
3
4
5
5
5
6
7
8
9
10