Self-Diagnosis Modes; Starting Each Mode; Exiting From Each Mode; List Of Modes - Toshiba e-STUDIO206L Service Manual

5.

SELF-DIAGNOSIS MODES

5.1 Overview
[A] Starting each mode
To enter the desired mode, turn the power ON while pressing two digital keys designated to each mode
(e.g. [0] and [5]) simultaneously. Hold the two keys until the [COPY] [e-FILING] [SCAN] [PRINT] [FAX]
buttons are lit.
Notes:
The above buttons do not light in e-STUDIO207L/257/307/357/457/507. Therefore, press two
digital keys until a "pip" sound is heard.
On the authentication screen displayed after starting up each mode, enter the service password, and
then press [OK]. The password is not set by default.
Refer to chapter 15 for the codes in Test mode (03), Test print mode (04), Adjustment mode (05), and
Setting mode (08).
[B] Exiting from each mode
Shut down the equipment. When the power should be turned OFF, be sure to shut down the equipment
by pressing the [ON/OFF] button for a few seconds.
[C] List of modes
Mode For start
Control panel [0] + [1] + [POWER]
check mode
Test mode [0] + [3] + [POWER]
Test print [0] + [4] + [POWER]
mode
Adjustment [0] + [5] + [POWER]
mode
Setting mode [0] + [8] + [POWER]
Assist mode [3] + [CLEAR] +
[POWER]
HDD assist [4]+[CLEAR]+
mode [POWER]
File system [5] + [CLEAR] +
recovery [POWER]
mode
SRAM clear [6]+[CLEAR]+
mode [POWER]
List print [9] + [START] +
mode [POWER]
PM support [6] + [START] +
mode [POWER]
EPU [7] + [START]
replacement + [POWER]
mode
Firmware [4] + [9] +
update mode [POWER]
[8] + [9] +
[POWER]
© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved
Contents
All LEDs on the control panel are lit, and all
the LCD pixels blink.
Checks the status of input/output signals.
Outputs the test patterns.
Adjusts various items.
Sets various items.
Clears error flags or SRAM, or safely
deletes data in the HDD or SRAM to support
the replacement of the SYS board, SRAM or
HDD.
Assists the ADI-HDD by checking the type of
the mounted HDD, reverting the HDD to a
factory default or removing keys.
Checks, recovers or initializes the file
system (HDD).
Recovers the equipment from particular
errors such as F800 or F900.
Prints various lists or outputs them in a CSV
format.
Clears each counter.
When replacing EPU, this mode is available
for the installation of the EPU whose initial
detection is possible.
Performs firmware update with USB media.
Performs firmware update with download jig. [POWER]
e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507
5 - 1
For exit Display
[POWER]
OFF/ON
[POWER] 100% C A4
OFF/ON TEST MODE
[POWER] 100% P A4
OFF/ON TEST PRINT
[POWER] 100% A A4
OFF/ON TEST MODE
[POWER] 100% D
OFF/ON TEST MODE
[POWER] -
OFF/ON
[POWER] -
OFF/ON
[POWER] -
OFF/ON
[POWER] -
OFF/ON
[POWER] 100% L A4
OFF/ON LIST PRINT
[POWER] 100% K
OFF/ON TEST MODE
[POWER]
OFF/ON
[POWER] -
OFF/ON
-
OFF/ON
SELF-DIAGNOSIS MODES
5