ABB ACS355 series User Manual page 181

The default values for the AC500 Modbus application macro correspond to the ABB
Standard macro with some differences, see section
117.
Index Name/ ABB
Selection STANDARD
9902 APPLIC 1 =
MACRO ABB
STANDARD
1001 EXT1 2 =
COMMANDS
1002 EXT2 0 =
COMMANDS SEL
1003 DIRECTION 3 =
REQUEST
1102 EXT1/EXT2 0 =
SEL
1103 REF1 SELECT 1 =
1106 REF2 SELECT 2 =
1201 CONST 9 =
SPEED SEL
1304 MINIMUM AI2 1.0%
1501 AO1 103
CONTENT SEL
1601 RUN ENABLE 0 =
SEL
2201 ACC/DEC 1/2 5 =
SEL
3201 SUPERV 1 103
PARAM
3401 SIGNAL1 103
PARAM
9904 MOTOR CTRL 3 =
MODE SCALAR:
FREQ
Note: It is possible to control several functions with one input (DI or AI), and there is a
chance of mismatch between these functions. In some cases it is desired to control
several functions with one input.
For example in the ABB standard macro, DI3 and DI4 are set to control constant
speeds. On the other hand, it is possible to select value 6 (DI3U,4D) for parameter
1103 REF1 SELECT. That would mean a mismatched duplicate functionality for DI3
and DI4: either constant speed or acceleration and deceleration. The function that is
not required must be disabled. In this case the constant speed selection must be
disabled by setting parameter
not related to DI3 and DI4.
Remember to also check the default values of the selected macro when configuring
the drive inputs.
3-WIRE ALTERNA
TE
2 = 3 =
3-WIRE ALTERNAT
E
DI1,2 4 = 9 =
DI1P,2P,3
NOT 0 = NOT 0 =
SEL SEL
3 = 3 =
REQUEST REQUEST
EXT1 0 = EXT1 0 =
AI1 1 = AI1 1 =
AI2 2 = AI2 2 =
DI3,4 10 = DI4,5 9 =
1.0% 1.0%
102 102
NOT 0 = NOT 0 =
SEL SEL
DI5 0 = NOT 5 =
SEL
102 102
102 102
1 = 1 =
VECTOR: VECTOR:
SPEED SPEED
1201 CONST SPEED SEL
Actual signals and parameters 181
AC500 Modbus macro
MOTOR HAND/
POT AUTO
4 = 5 =
MOTOR HAND/AUT
POT O
DI1F,2R 2 = DI1,2 2 =
NOT 0 = NOT 21 =
SEL
3 = 3 =
REQUEST REQUEST
EXT1 0 = EXT1 3 =
AI1 12 = 1 =
DI3U,4D(N
C)
AI2 2 = AI2 2 =
DI3,4 5 = DI5 0 =
SEL
1.0% 20.0%
102 102
NOT 0 = NOT 0 =
SEL SEL
DI5 0 = NOT 0 =
SEL SEL
102 102
102 102
1 = 1 =
VECTOR: VECTOR:
SPEED SPEED
to
on page
PID TORQUE
CONTROL CONTROL
6 = 7 =
PID TORQUE
CONTROL CTRL
DI1,2 20 = DI5 2 =
DI5,4 1 = DI1 2 =
1 = 3 =
FORWARD REQUEST
DI3 -2 = 3 =
DI2(INV)
AI1 1 = AI1 1 =
AI2 19 = 2 =
PID1OUT
NOT 3 = DI3 4 =
20.0% 20.0%
102 102
NOT 4 = DI4 0 =
SEL
NOT 0 = NOT 5 =
SEL
102 102
102 102
3 = 2 =
SCALAR: VECTOR:
FREQ TORQ
NOT SEL or to values
DI1,2
DI1,2
DI3
AI1
AI2
DI4
NOT
DI5