Ie Ip Address Of Station / Ie Ip Of Stat; Ie Default Gateway Of Station / Ie Def Gateway; Ie Subnet Mask Of Station / Ie Subnet Mask; Ie Dhcp Mode / Ie Dhcp Mode - Siemens SINAMICS G150 Manual

2 Parameters
2.2 List of parameters
Dependency: Refer to: p8905, r8910
Note: An ASCII table (excerpt) can be found, for example, in the appendix to the List Manual.
The interface configuration (p8900 and following) is activated with p8905 = 1.
The parameter is not influenced by setting the factory setting.
IE: Industrial Ethernet
p8901[0...3]

IE IP Address of Station / IE IP of Stat

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Unsigned8
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
0
Description: Sets the IP address for the Industrial Ethernet interface (X127) on the Control Unit.
The active IP address is displayed in r8911.
Dependency: Refer to: p8905, r8911
Note: The interface configuration (p8900 and following) is activated with p8905 = 1.
The parameter is not influenced by setting the factory setting.
p8902[0...3]

IE Default Gateway of Station / IE Def Gateway

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Unsigned8
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
0
Description: Sets the default gateway for the Industrial Ethernet interface (X127) on the Control Unit.
The active default gateway is displayed in r8912.
Dependency: Refer to: p8905, r8912
Note: The interface configuration (p8900 and following) is activated with p8905 = 1.
The parameter is not influenced by setting the factory setting.
p8903[0...3]

IE Subnet Mask of Station / IE Subnet Mask

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Unsigned8
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
0
Description: Sets the subnet mask for the Industrial Ethernet interface (X127) on the Control Unit.
The active subnet mask is displayed in r8913.
Dependency: Refer to: p8905, r8913
Note: The interface configuration (p8900 and following) is activated with p8905 = 1.
The parameter is not influenced by setting the factory setting.
p8904

IE DHCP mode / IE DHCP mode

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Unsigned8
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
0
Description: Sets the DHCP mode for the Industrial Ethernet interface (X127) on the Control Unit.
820
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
3
List Manual (LH2), 04/2014, A5E03263479A
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
SINAMICS G130/G150