Pn Name Of Station Active / Pn Name Stat Act; Pn Ip Address Of Station Active / Pn Ip Of Stat Act; Pn Default Gateway Of Station Active / Pn Def Gateway Act; Pn Subnet Mask Of Station Active / Pn Subnet Mask Act - Siemens SINAMICS G150 Manual

2 Parameters
2.2 List of parameters
r8930[0...239]

PN Name of Station active / PN Name Stat act

CU_G130_PN, Can be changed: -
CU_G150_PN
Data type: Unsigned8
P-Group: -
Not for motor type: -
Min
-
Description: Displays the active station name for the onboard PROFINET interface on the Control Unit.
r8931[0...3]

PN IP Address of Station active / PN IP of Stat act

CU_G130_PN, Can be changed: -
CU_G150_PN
Data type: Unsigned8
P-Group: -
Not for motor type: -
Min
0
Description: Displays the active IP address for the onboard PROFINET interface on the Control Unit.
r8932[0...3]

PN Default Gateway of Station active / PN Def Gateway act

CU_G130_PN, Can be changed: -
CU_G150_PN
Data type: Unsigned8
P-Group: -
Not for motor type: -
Min
0
Description: Displays the active default gateway for the onboard PROFINET interface on the Control Unit.
r8933[0...3]

PN Subnet Mask of Station active / PN Subnet Mask act

CU_G130_PN, Can be changed: -
CU_G150_PN
Data type: Unsigned8
P-Group: -
Not for motor type: -
Min
0
Description: Displays the active subnet mask for the onboard PROFINET interface on the Control Unit.
r8934 PN DHCP Mode active / PN DHCP Mode act
CU_G130_PN, Can be changed: -
CU_G150_PN
Data type: Unsigned8
P-Group: -
Not for motor type: -
Min
0
Description: Displays the active DHCP mode for the onboard PROFINET interface on the Control Unit.
Notice: When the DHCP mode is active (parameter value greater than 0), PROFINET communication via this interface is no
longer possible! However, the interface can be used for commissioning tool such as STARTER or SCOUT.
Note: If value = 0:
DHCP deactivated.
If value = 2:
DHCP activated. The MAC address of this interface is used for client identification.
If value = 3:
DHCP activated. The station name of this interface is used for client identification.
826
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
List Manual (LH2), 04/2014, A5E03263479A
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
SINAMICS G130/G150