Isq Controller Integral Component / Isq_Ctrl I_Comp; Co: Isd Controller Output / Isd_Ctrl Outp; Isd Controller Integral Component / Isd_Ctrl I_Comp; Isd Controller Integral Component Limit / Isd_Ctrl I_Limit - Siemens SINAMICS G150 Manual

r1719

Isq controller integral component / Isq_ctrl I_comp

VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
- [Vrms]
Description: Displays the integral component of the Isq current controller (torque/force-generating current, PI controller).
r1723

CO: Isd controller output / Isd_ctrl outp

VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
- [Vrms]
Description: Displays the actual output of the Isd current controller (flux-generating current, PI controller).
The value contains the proportional and integral components of the PI controller.
r1724

Isd controller integral component / Isd_ctrl I_comp

VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
- [Vrms]
Description: Displays the integral component of the Isd current controller (flux-generating current, PI controller).
r1725

Isd controller integral component limit / Isd_ctrl I_limit

VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
- [Vrms]
Description: Displays the limit value for the integral component of the Isd current controller.
p1726[0...n] Quadrature arm decoupling scaling / Transv_decpl scal
VECTOR_G (n/M) Can be changed: U, T
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
0.0 [%]
Description: Sets the scaling of the quadrature arm decoupling
Note: This parameter is ineffective for sensorless vector control. In this case, p1727 is always used. If p1726 is set to 0,
then the quadrature de-coupling is de-activated. The integral component of the Isd current controller remains
effective in the complete speed control range.
For the closed-loop control of synchronous motors, this parameter is used to scale the current controller de-coupling.
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Calculated: -
Dyn. index: -
Units group: 5_1
Scaling: p2001
Max
- [Vrms]
Calculated: -
Dyn. index: -
Units group: 5_1
Scaling: p2001
Max
- [Vrms]
Calculated: -
Dyn. index: -
Units group: 5_1
Scaling: p2001
Max
- [Vrms]
Calculated: -
Dyn. index: -
Units group: 5_1
Scaling: p2001
Max
- [Vrms]
Calculated: CALC_MOD_ALL
Dyn. index: DDS, p0180
Units group: -
Scaling: -
Max
200.0 [%]
2 Parameters
2.2 List of parameters
Access level: 4
Func. diagram: 6714
Unit selection: p0505
Expert list: 1
Factory setting
- [Vrms]
Access level: 4
Func. diagram: 6714
Unit selection: p0505
Expert list: 1
Factory setting
- [Vrms]
Access level: 4
Func. diagram: 6714
Unit selection: p0505
Expert list: 1
Factory setting
- [Vrms]
Access level: 4
Func. diagram: 6714
Unit selection: p0505
Expert list: 1
Factory setting
- [Vrms]
Access level: 4
Func. diagram: 6714
Unit selection: -
Expert list: 1
Factory setting
75.0 [%]
413