Comm Board Monitoring Time / Cb T_Monit; Comm Board Send Configuration Data / Cb S Config_Dat; Activate Comm Board Send Configuration / Cb S Config Act - Siemens SINAMICS G150 Manual

- CAN CBC10 always communicates via IF2.
For a value not equal to 99 (automatic) the following applies:
- both indices must be set to a number not equal to 99 (automatic).
A change only becomes effective after POWER ON, reset or download.
p8840

COMM BOARD monitoring time / CB t_monit

CU_G130_DP (COMM Can be changed: U, T
BOARD, PROFINET
Data type: FloatingPoint32
CBE20),
P-Group: Communications
CU_G130_PN (COMM
Not for motor type: -
BOARD, PROFINET
CBE20),
Min
CU_G150_DP (COMM
0 [ms]
BOARD, PROFINET
CBE20),
CU_G150_PN (COMM
BOARD, PROFINET
CBE20)
Description: Sets the monitoring time to monitor the process data received via COMM BOARD.
If, during this time, the Control Unit does not receive any process data from the COMM BOARD, then an appropriate
message is output.
Note: This monitoring function only monitors the connection between the Control Unit and COMM BOARD and not the data
traffic on the fieldbus.
Value = 0: Monitoring is de-activated.
p8841[0...239]

COMM BOARD send configuration data / CB s config_dat

CU_G130_DP (COMM Can be changed: U, T
BOARD, PROFINET
Data type: Unsigned16
CBE20),
P-Group: Communications
CU_G130_PN (COMM
Not for motor type: -
BOARD, PROFINET
CBE20),
Min
CU_G150_DP (COMM
0
BOARD, PROFINET
CBE20),
CU_G150_PN (COMM
BOARD, PROFINET
CBE20)
Description: Sets the send configuration data for the COMM BOARD.
The setting is activated with p8842.
Dependency: Refer to: p8842
Note: The configuration data are specific to the inserted COMM BOARD.
For CBE20, the configuration data are not relevant.
p8842

Activate COMM BOARD send configuration / CB s config act

CU_G130_DP (COMM Can be changed: U, T
BOARD, PROFINET
Data type: Unsigned16
CBE20),
P-Group: Communications
CU_G130_PN (COMM
Not for motor type: -
BOARD, PROFINET
CBE20),
Min
CU_G150_DP (COMM
0
BOARD, PROFINET
CBE20),
CU_G150_PN (COMM
BOARD, PROFINET
CBE20)
Description: Activate a modified send configuration for COMM BOARD.
With p8842 = 1, the values in p8841 are transferred to the COMM BOARD and activated. After this, p8842 is
automatically set to zero.
Dependency: Refer to: p8841
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
65535000 [ms]
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
65535
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1
2 Parameters
2.2 List of parameters
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
20 [ms]
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
787