Table 1.5C Pin Functions (3/4) - Fujitsu F2MC-16LX MB90580 Series Hardware Manual

QFP LQFP
45 43
46 44
27 25
28 26
29 27
32 30
33 31
47 45
48 46
53 51
54 52
55 53
56 54
57 55
58 56
59 57
60 58
61 59
MB90580 series

Table 1.5c Pin functions (3/4)

Pin name I/O Circuit
P56
G
AN6
(CMOS/H)
SCK4
P57
G
(CMOS/H)
AN7
C
F
P71
(CMOS/H)
F
P72
(CMOS/H)
P73
H
(CMOS/H)
DAO0
P74
F
(CMOS/H)
DAO1
P80
F
(CMOS/H)
IRQ0
P81
F
(CMOS/H)
IRQ1
P82
F
(CMOS/H)
IRQ2
P83
F
(CMOS/H)
IRQ3
P84
F
(CMOS/H)
IRQ4
P85
F
(CMOS/H)
IRQ5
P86
F
(CMOS/H)
IRQ6
P87
F
(CMOS/H)
IRQ7
P60
D
(CMOS/H)
SIN2
D
P61
(CMOS/H)
SOT2
D
P62
(CMOS/H)
SCK2
General-purpose I/O port
Analog input pin (AN6) during A/D converter operation
UART4 serial data output (SOT4) pin
General-purpose I/O port
Analog input pins (AN7) during A/D converter operation
0.1uf capacitor connection pin for voltage supply stabilization.
General-purpose I/O port
SOT3 pin when the SOE bit of the UMC register is '1'
General-purpose I/O port
Clock input (SCK3) during UART1 operation in external shift clock mode
SCK3 pin when the SOE bit of the UMC register is '1'
General-purpose I/O port
D/A output pin when the DAE0 bit of the D/A control register (DACR) is '1'
D/A output '0' pin during D/A converter operation
General-purpose I/O port
D/A output pin when the DAE1 bit of the D/A control register (DACR) is '1'
D/A output '1' pin during D/A converter operation
General-purpose I/O port
External interrupt request I/O 0
General-purpose I/O port
External interrupt request I/O 1
General-purpose I/O port
External interrupt request I/O 2
General-purpose I/O port
External interrupt request I/O 3
General-purpose I/O port
External interrupt request I/O 4
General-purpose I/O port
External interrupt request I/O 5
General-purpose I/O port
Always enabled (STBC)
External interrupt request I/O 6
General-purpose I/O port
Always enabled (STBC)
External interrupt request I/O 7
General-purpose I/O port
A pull-up resistor can be assigned (RD60='1') by using the pull-up resistor
setting register (RDR6). (D60='1': Invalid when set as output)
UART2 serial data input (SIN2) pin
General-purpose I/O port
SOT1 pin when the SOE bit of the UMC register is '1'
A pull-up resistor can be assigned (RD61='1') by using the pull-up resistor
setting register (RDR6). (D61='1': Invalid when set as output)
UART2 serial data output (SOUT2) pin
General-purpose I/O port
Clock input (SCK2) during UART1 operation in external shift clock mode
SCK1 pin when the SOE bit of the UMC register is '1'
A pull-up resistor can be assigned (RD62='1') by using the pull-up resistor
setting register (RDR6). (D62='1': Invalid when set as output)
UART2 serial clock I/O (SCK2) pin
1.5 Pin Functions
Function
Chapter 1: Overview 9