Toshiba GR200 Series Instruction Manual page 559

Remote/Local end
"
SPOS01_SL_BO_FLG
(510001_8501011F76)
Select
command
ON/OFF
"
SPOS01_OEX_BO
(510001_8201011DD3)
Operate-On
command
"
SPOS01_FEX_BO
(510001_8101011DD0)
Operate-Off
command
Figure 4.1-39 Contact health check setting and 43SW diagram for example #3
Table 4.1-25 PLC monitoring points (Output signal for event suppression function in SPOSxx)
Signal Number
510001 0001011001
510001 0001021001
510001 0001031001
....
510001 0001141001
510001 8101011F59
510001 8101021F59
510001 8101031F59
....
510001 8101141F59
Table 4.1-26 PLC monitoring points (Output of select signal in SPOSxx)
Signal Number
510001 8501011F76
510001 8501021F76
510001 8501031F76
....
510001 8501141F76
Table 4.1-27 PLC monitoring points (Output of operate signal in SPOSxx)
Signal Number
510001 8201011DD3
510001 8201021DD3
510001 8201031DD3
...
510001 8201141DD3
510001 8101011DD0
510001 8101021DD0
510001 8101031DD0
...
"
"
" "
BO2-RB
"
(200B01_8102011113)
" "
BO3-RB
(200B01_8202021113)
Signal Name
SPOS01_STATE
SPOS02_STATE
SPOS03_STATE
....
SPOS20_STATE
SPOS01_F_QLT_SPP
SPOS02_F_QLT_SPP
SPOS03_F_QLT_SPP
....
SPOS20_F_QLT_SPP
Signal Name
SPOS01_SL_BO_FLG
SPOS02_SL_BO_FLG
SPOS03_SL_BO_FLG
....
SPOS20_SL_BO_FLG
Signal Name
SPOS01_OEX_BO
SPOS02_OEX_BO
SPOS03_OEX_BO
...
SPOS20_OEX_BO
SPOS01_FEX_BO
SPOS02_FEX_BO
SPOS03_FEX_BO
....
- 538 -
BIO module
Plus (+)
SW1 is not driven with
any BO1
SW2 is driven with
BO2 at IO#1
BO2
SW3 is driven with
BO3 at IO#1
BO3
Description
Status of SPOS01
Status of SPOS02
Status of SPOS03
....
Status of SPOS20
Event suppression detected (SPOS01)
Event suppression detected (SPOS02)
Event suppression detected (SPOS03)
....
Event suppression detected (SPOS20)
Description
Select command signal in SPOS01
Select command signal in SPOS02
Select command signal in SPOS03
....
Select command signal in SPOS20
Description
SPOS01 operate (ON) command for Binary Output.
SPOS02 operate (ON) command for Binary Output.
SPOS03 operate (ON) command for Binary Output.
...
SPOS20 operate (ON) command for Binary Output.
SPOS01 operate (OFF) command for Binary Output.
SPOS02 operate (OFF) command for Binary Output.
SPOS03 operate (OFF) command for Binary Output.
....
6F2S1915 (0.46)
43SW
Plus (+)
SW 1
Physical BO is
virtualized.
On
SW 2
Command
SW 3
Off
Command
Minus (−)
GRZ200 (Soft 031 & 032)