Mitsubishi Electric C70 Setup Manual page 562

Error No. Error message
E50 FILE ERROR
E51 FILE OPEN ERROR
E52 FILE CLOSE ERR
E53 FILE SEEK ERR
E54 FILE READ ERR
E55 FILE DELETE ERR
E56 FILE INSERT ERR
E60 IOP ERR **
E62 I/O PARAM ERR
E64 PROGRAM No. ERR
E65 PROG. No. DUPLl
E66 NO PROG. NUMBER
E69 PROG. CHECK MODE
E70 TOOL No. DUPLl
E71 TOOL ENTRY OVER
E76 TOOL No. ERROR
E77 AXIS NO REF-RET
E78 AX UNMATCH (TLM )
E79 NO REF-RTN (TLM)
E81 PROGRAM ERROR
E82 ALREADY RESEARCH
E84
CAN'T IN/OUT
Appendix 2.15 Operation Messages on Setting Display Unit
- If one of these errors occurs‚ the editing or input/output operations cannot be
continued. Contact the service center.
×
As for E50‚ a classification No. will display at the end of the message. Inform the
service center of this No. as well.
A classification number is displayed after the message for E60.
Refer to the section shown in parentheses‚ and remedy the problem.
E60 lOP ERROR – 4 (E09 time out)
E60 lOP ERROR – 5 (E08 physical err)
E60 lOP ERROR – 7 (E07 reset end)
E60 lOP ERROR – 10 (E04 DEV. NOT READY)
E60 lOP ERROR – 15 (E17 parity H err)
×
E60 lOP ERROR – 16 (E18 parity V err)
E60 lOP ERROR – 17 (E20 over run error)
E60 lOP ERROR – 18 (E22 code change error)
E60 IOP ERROR – 20 (framing and H/W errors)
- Setting for the bit length is incorrect. (Baud rate, stop bit, and character length)
Check the setting of the I/O device system and its parameters and set it again.
- Check the situations of the connected devices (cable wiring and noise measures).
- The "EIA code" data set for I/O parameter is of an unusable code.
Δ
The unusable codes are those used as the EIA standard codes and the even hole
codes.
- The same No. as the program No. designated for program copy was found in the
memory.
Δ
- During tape input‚ the first character of the machining program block is the program
No. address "O" or "L".
Δ - During tape input‚ the same No. as the specified program was found in the memory.
- During tape input‚ the program No. was not found on the paper tape‚ and a program
Δ
No. was not designated on the screen' s data setting area. Set the program No.‚ and
input again.
- Search (operation search) was attempted during program check (continuous or
step).
×
Retry search after the program check is completed‚ or after resetting the program
search
- A tool No. already registered was newly registered on the tool life management
Δ
screen.
- Registration of data exceeding the max. No. of registerable tools was attempted on
the tool life management screen.
× - When inputting the tool offset data onto tape‚ a compensation number exceeding
the specifications range was specified‚ and that block could not be input. If the input
key is pressed again in the input screen‚ the input will continue from the next block.
- The offset No. to be used for workpiece coordinate system offset data
× measurement was invalid. Restart from tool selection. (Correctly specify the R
register that contains the offset number.)
- Zero point return has not been completed for the axis being measured. Return the
×
axis to the zero point.
- During movement of two or more axes‚ the sensor turned on and the tool length was
× measured.
Keep off from the sensor and perform the measurement for one axis at a time.
- The sensor turned on for an axis that has not completed dog- type reference point
× return‚ and the tool length was measured. Return the axis to measure to the
reference point.
- A program error was detected while searching the designated block. Refer to the
×
directions for the responding program error code being displayed at the same time.
- Immediately after completing a restart search in program restart, another search or
restart search was attempted. If program restart operation is continued, the program
× will restart from the block searched in the previous search (the axis will be returned
to the restart position automatically or manually). To start over a search, cancel the
previous search by resetting, and then search again.
- Parameters were input in the setup parameter lock state.
Refer to the instruction manual issued by the machine maker.
×
- When using the high-speed program server function, the parameter "#1925
EtherNet" parameter was set to "0".
C70 Setup Manual
Details
545