Mitsubishi Electric FR-A820-00046 (0.4K) Instruction Manual page 209

Pr.
Pr.
group
G021 113
G030 60
G040 100
G041 101
G042 102
G043 103
G044 104
G045 105
G046 106
G047 107
G048 108
G049 109
G060 673
G061 674
G080 617
G100 10
G101 11
G102 802
G103 850
G105 522
G106 250
*3
G107
70
G108 1299
G110 12
G120 882
G121 883
G122 884
G123 885
G124 886
G125 665
G130 660
G131 661
G132 662
G200 800
G201 85
G202 86
G203 245
208
5. PARAMETERS
5.1 Parameter list
Name
Third V/F (base frequency)
Energy saving control
selection
V/F1 (first frequency)
V/F1 (first frequency voltage)
V/F2 (second frequency)
V/F2 (second frequency
voltage)
V/F3 (third frequency)
V/F3 (third frequency voltage)
V/F4 (fourth frequency)
V/F4 (fourth frequency voltage)
V/F5 (fifth frequency)
V/F5 (fifth frequency voltage)
SF-PR slip amount adjustment
operation selection
SF-PR slip amount adjustment
gain
Reverse rotation excitation
current low-speed scaling
factor
DC injection brake operation
frequency
DC injection brake operation
time
Pre-excitation selection
Brake operation selection
Output stop frequency
Stop selection
Special regenerative brake
duty
Second pre-excitation
selection
DC injection brake operation
voltage
Regeneration avoidance
operation selection
Regeneration avoidance
operation level
Regeneration avoidance at
deceleration detection
sensitivity
Regeneration avoidance
compensation frequency limit
value
Regeneration avoidance
voltage gain
Regeneration avoidance
frequency gain
Increased magnetic excitation
deceleration operation
selection
Magnetic excitation increase
rate
Increased magnetic excitation
current level
Control method selection
Excitation current break point
Excitation current low speed
scaling factor
Rated slip
Refer
Pr.
to Pr.
group
page
673
G204 246
678
G205 247
679
679
G206 1116
679
G210 803
679
G211 820
679
G212 821
679
679
G213 824
679
679
G214 825
679
*1
G215
823
680
G216 827
680
G217 854
G218 1115
677
G220 877
681
G221 878
681
G222 879
681
G223 881
681
G224 828
686
G230 840
688
G231 841
689
G232 842
G233 843
681
G234 844
G235 845
681
G236 846
696
G237 847
696
G238 848
696
*1
G240
367
*1
G241
368
696
G250 788
G260 1121
696
G261 1117
696
G262 1119
699
G263 1348
699
G264 1349
699
G300 451
215
677
G301 565
677
G302 566
700
Name
Slip compensation time
constant
Constant output range slip
compensation selection
Constant output range speed
control P gain compensation
Constant output range torque
characteristic selection
Speed control P gain 1
Speed control integral time 1
Torque control P gain 1
(current loop proportional
gain)
Torque control integral time 1
(current loop integral time)
Speed detection filter 1
Torque detection filter 1
Excitation ratio
Speed control integral term
clear time
Speed feed forward control/
model adaptive speed control
selection
Speed feed forward filter
Speed feed forward torque
limit
Speed feed forward gain
Model speed control gain
Torque bias selection
Torque bias 1
Torque bias 2
Torque bias 3
Torque bias filter
Torque bias operation time
Torque bias balance
compensation
Fall-time torque bias terminal 1
bias
Fall-time torque bias terminal 1
gain
Speed feedback range
Feedback gain
Low speed range torque
characteristic selection
Per-unit speed control
reference frequency
Speed control P gain 1 (per-
unit system)
Model speed control gain (per-
unit system)
P/PI control switchover
frequency
Emergency stop operation
selection
Second motor control method
selection
Second motor excitation
current break point
Second motor excitation
current low-speed scaling
factor
Refer
to
page
700
700
244
235,
270
244
244
280,
317
280,
317
316
316
316
244
253
253
253
253
253
255
255
255
255
255
255
255
255
255
700
700
227
244
244
253
244
349
215
677
677