Mitsubishi Electric FR-A820-00046 (0.4K) Instruction Manual page 812

Frame Number: 160M, 160L, 180M, 180L
Terminal box for cooling fan
Connector (for encoder)
MS3102A20-29P
L
A
B
KA
Main
Exhaust
terminal box
Suction
1, 2
Direction of
Mark for earthing
cooling fan wind
(grounding)
F F
Earth (ground)
N
terminal (M8)
W Sliding distance
X
S
Frame leg viewed
Section AA
from above
Terminal box for cooling fan
Main terminal box
For motor (U, V, W)
Earthing
(grounding)
U V W
terminal (M8)
B1 B2 G1 G2
For brake (B1, B2) For thermal protector (G1, G2)
Dimensions table (Unit: mm)
SF- SF- SF- SF-
Frame Mass
V5RU V5RU V5RU V5RU
No. (kg)
A B
[]KB []K1B []K3B []K4B
11 7 5 2 160M 140 522.5 198 160 318
15 11 7 3 160L 155 544.5 220 160 318
18 — — — 185
180M 568.5 225.5 180 363 139.5 120.5 8
22 15 11 — 215
— 18 15 5 180L 255 587.5 242.5 180 363 139.5 139.5 8
30 — — 7 305
200L 644.5 267.5 200 406
37, 45 22, 30 18, 22 — 330
55 37 30 11, 15 225S 395 659 277 225 446
NOTE
• Install the motor on the floor and use it with the shaft horizontal.
• Leave an enough clearance between the fan suction port and wall to ensure adequate cooling. Check that a fan blows air from
the opposite load side to the load side.
• The vertical tolerance for the shaft center height is
• The 400 V class motor has "-H" at the end of its model name.
• Since a brake power device is a stand-alone, install it inside the enclosure. (This device should be arranged by the customer.
Refer to the FR-A800 catalog.)
R
KL
110
D
90
1
A
2
A
J
XB
E
E
M
For cooling fan (A, B, C)
A B C
Earthing (grounding)
terminal (M4)
Motor
C D E F G H I J KA KD KG KL
127 105 8 — — 50 105 56 115 330 391 845.5 310
127 127 8 — — 50 127 56 115 330 391 889.5 310
— — 50 127 56 139 352 428 920 335
— — 50 146 56 139 352 428 958 335
159 152.5 11 — — 70 145 90 487
178 143 11 — — 70 145 90 533
Frame number: 200L, 225S
Connector (for encoder)
Terminal box for cooling fan
MS3102A20-29P
L
A
KA
φ22
Main
terminal box
Suction
1, 2
Mark for earthing
Direction of
(grounding) F F
cooling fan wind
N
Earth (ground)
terminal (M12)
 indicates an inserting position of a bolt with hex head holes for
manual opening.
Make sure to earth the earth terminal of the flange section as well as
the earth terminal in the terminal box.
KP L M ML N X XB
— 254 4 108 14.5 110 90
— 298 4 108 14.5 110 90
— 285 4 121 14.5 110 90 351.5 48k6
— 323 4 121 14.5 110 90 370.5 55m6 10
— 546 1070 390 — 361 4 133 18.5 140 110 425.5 60m6 11
— 592 1091 428 — 342 4 149 18.5 140 110 432 65m6 11
.
0
-0.5
R
B 140 D
110
Exhaust
1
A
A
J
XB
E E
M
W
Sliding distance
S
Frame leg viewed
Section AA
from above
Shaft end Terminal screw size
U, V, A, B,
Z Q QK R S T U W
W (C)
323 42k6 8 5 12 M8 M4
345 42k6 8 5 12 M8 M4
9 5.5 14 M8 M4
6 16 M8 M4
7 18 M10 M4
7 18 M10 M4
8. SPECIFICATIONS
8.4 Outline dimension drawings
1
2
3
2
4
X
5
6
7
8
9
G1, B1,
G2 B2
10
M4 M4
M4 M4
M4 M4
M4 M4
M4 M4
M4 M4
813