Mitsubishi Electric FR-A800 Series Instruction Manual page 215

Pr. group Pr.
G061 674
G080 617
G100 10
G101 11
G102 802
G103 850
G105 522
G106 250
*3
G107
70
G108 1299
G110 12
G120 882
G121 883
G122 884
G123 885
G124 886
G125 665
G130 660
G131 661
G132 662
G200 800
G201 85
G202 86
G203 245
G204 246
G205 247
G206 1116
G210 803
G211 820
G212 821
G213 824
G214 825
*1
G215
823
G216 827
G217 854
214
5. PARAMETERS
5.1 Parameter list
Downloaded from ManualsNet.com
Name
SF-PR slip amount adjustment
gain
Reverse rotation excitation
current low-speed scaling
factor
DC injection brake operation
frequency
DC injection brake operation
time
Pre-excitation selection
Brake operation selection
Output stop frequency
Stop selection
Special regenerative brake
duty
Second pre-excitation
selection
DC injection brake operation
voltage
Regeneration avoidance
operation selection
Regeneration avoidance
operation level
Regeneration avoidance at
deceleration detection
sensitivity
Regeneration avoidance
compensation frequency limit
value
Regeneration avoidance
voltage gain
Regeneration avoidance
frequency gain
Increased magnetic excitation
deceleration operation
selection
Magnetic excitation increase
rate
Increased magnetic excitation
current level
Control method selection
Excitation current break point
Excitation current low-speed
scaling factor
Rated slip
Slip compensation time
constant
Constant output range slip
compensation selection
Constant output range speed
control P gain compensation
Constant output range torque
characteristic selection
Speed control P gain 1
Speed control integral time 1
Torque control P gain 1
(current loop proportional
gain)
Torque control integral time 1
(current loop integral time)
Speed detection filter 1
Torque detection filter 1
Excitation ratio
search engine
Refer
Pr. group Pr.
to page
714 G218 1115
711 G220 877
G221 878
715
G222 879
715
G223 881
715
G224 828
715
G230 840
720
G231 841
722
G232 842
G233 843
724
G234 844
G235 845
715
G236 846
715
G237 847
732
G238 848
732
*1
G240
367
*1
G241
732 368
G250 788
732
G260 1121
732
G261 1117
732
G262 1119
G263 1348
735
G264 1349
735
G300 451
735
G301 565
221
711
G302 566
711
736 G311 830
G312 831
736
G313 834
736
254
G314 835
245,
*1
G315
833
283
G316 837
254
254
G350 747
294,
333
G361 1118
294,
G400 286
333
G401 287
332
G402 288
332
332 G403 994
Name
Speed control integral term
clear time
Speed feed forward control/
model adaptive speed control
selection
Speed feed forward filter
Speed feed forward torque
limit
Speed feed forward gain
Model speed control gain
Torque bias selection
Torque bias 1
Torque bias 2
Torque bias 3
Torque bias filter
Torque bias operation time
Torque bias balance
compensation
Fall-time torque bias terminal 1
bias
Fall-time torque bias terminal 1
gain
Speed feedback range
Feedback gain
Low speed range torque
characteristic selection
Per-unit speed control
reference frequency
Speed control P gain 1 (per-
unit system)
Model speed control gain (per-
unit system)
P/PI control switchover
frequency
Emergency stop operation
selection
Second motor control method
selection
Second motor excitation
current break point
Second motor excitation
current low-speed scaling
factor
Speed control P gain 2
Speed control integral time 2
Torque control P gain 2
(current loop proportional
gain)
Torque control integral time 2
(current loop integral time)
Speed detection filter 2
Torque detection filter 2
Second motor low-speed
range torque characteristic
selection
Speed control P gain 2 (per-
unit system)
Droop gain
Droop filter time constant
Droop function activation
selection
Droop break point gain
Refer
to page
254
263
263
263
263
263
265
265
265
265
265
265
265
265
265
736
736
233
254
254
263
254
367
221
711
711
254
254
294
294
332
332
233
254
738
738
738
738