Mitsubishi Electric FR-A800 Series Instruction Manual page 460

Monitor item
Motor speed
Motor torque
Converter output
*2
voltage
Regenerative brake
*4
duty
Electronic thermal O/L
relay load factor
Output current peak
value
Converter output voltage
peak value
Input power
*2
Output power
Load meter
Motor excitation current
Reference voltage output —
Motor load factor
Torque command
Torque current command 0.1%
Motor output
Torque (positive polarity
for driving torque/
negative polarity for
regenerative braking
torque)
Motor temperature
Energy saving effect
PID set point
PID measured value
PID deviation
Motor thermal load factor 0.1%
Inverter thermal load
factor
PID measured value 2
PLC function analog
output
Remote output value 1
Remote output value 2
Remote output value 3
Remote output value 4
Downloaded from ManualsNet.com
Increment Pr.54 (FM/CA),
and unit Pr.158 (AM) setting
1 (r/min) 6
0.1% 7
0.1 V 8
0.1% 9
0.1% 10
*1
11
0.01/0.1 A
0.1 V 12
*1
13
0.01/0.1 kW
*1
14
0.01/0.1 kW
0.1% 17
*1
18
0.01 A/0.1 A
21
0.1% 24
0.1% 32
33
*1
34
0.01/0.1 kW
0.1% 36
1°C 46
Increment and
unit vary
depending on 50
the parameter
settings.
0.1% 52
0.1% 53
*5
0.1%
54
61
0.1% 62
0.1% 67
0.1% 70
0.1% 87
0.1% 88
0.1% 89
0.1% 90
search engine
Negative
Terminal FM, CA, AM
(-)
full-scale value
output
The value converted
*3
with the Pr.37, Pr.144
○
value from Pr.55.
Pr.866 ○
200 V class: 400 V,
400 V class: 800 V
Brake duty decided by
Pr.30, Pr.70.
Electronic thermal O/L
relay (100%)
Pr.56
200 V class: 400 V,
400 V class: 800 V
Inverter rated power ×
2
Inverter rated power ×
2
Pr.866
Pr.56
—
200%
Pr.866 ○
Pr.866 ○
Rated motor capacity
Pr.866 ○
Pr.751 ○
Inverter capacity
100%
100%
100% ○
Motor thermal
activation level
(100%)
Inverter thermal
activation level
(100%)
100%
100% ○
1000%
1000%
1000%
1000%
5.11 (M) Item and output signal for monitoring
Remarks
Refer to page 444 for the monitoring of
the operation speed.
Terminal FM: When Pr.291 = "0 or 1",
output is 1440 pulses/s. When Pr.291 ≠
"0 or 1", output is 50k pulses/s.
Terminal CA: Output is 20 mA.
Terminal AM: Output is 10 V.
Enabled when the FR-A8AZ is used.
For the information of the power saving
effect monitoring, refer to page 467.
Refer to page 610 for the PID control.
Refer to page 610 for the PID control.
Enabled by Pr.414 = "1 or 2".
Refer to page 646 for the PLC function.
Refer to page 490 for the analog
remote output.
5. PARAMETERS
1
2
3
4
5
6
7
8
9
10
459