Parameters (Functions) And Instruction Codes Under Different Control Methods - Mitsubishi Electric FR-A800 Series Instruction Manual

9.5
Parameters (functions) and instruction codes
under different control methods
*1 Instruction codes are used to read and write parameters in accordance with the Mitsubishi inverter protocol of RS-485 communication. (For RS-
485 communication, refer to
*2 Function availability under each control method is shown as follows:
○: Available
×: Not available
Δ: Available with some restrictions
*3 If function availability differs between using induction motors with an encoder and using PM motors with an encoder, the function availability using
PM motors with an encoder is described in parentheses. Also, a PM motor with an encoder is not available in the torque control mode.
*4 For Parameter copy, Parameter clear, and All parameter clear, ○ indicates the function is available, and × indicates the function is not available.
*5 Communication parameters that are not cleared by parameter clear or all clear (H5A5A or H55AA) via communication. (For RS-485
communication, refer to
*6 When a communication option is installed, parameter clear (lock release) during password lock (Pr.297 Password lock/unlock ≠ "9999") can be
performed only from the communication option.
*7 Available when the IPM motor MM-CF series is used and the low-speed range high-torque characteristic is enabled (Pr.788 Low speed range
torque characteristic selection = "9999 (initial value)").
*8 Reading and writing via the PU connector are available.
Symbols in the table indicate parameters that operate when the options are connected.
FR-A8AP, FR-A8AL,
A8AY, FR-A8AZ,
FR-A8NS
Pr.
0 Torque boost
1 Maximum frequency
2 Minimum frequency
3 Base frequency
4 Multi-speed setting (high speed)
Multi-speed setting (middle
5
speed)
6 Multi-speed setting (low speed)
7 Acceleration time
8 Deceleration time
9 Electronic thermal O/L relay
DC injection brake operation
10
frequency
DC injection brake operation
11
time
DC injection brake operation
12
voltage
13 Starting frequency
14 Load pattern selection
15 Jog frequency
Jog acceleration/deceleration
16
time
17 MRS input selection
18 High speed maximum frequency
19 Base frequency voltage
Acceleration/deceleration
20
reference frequency
864
9. APPENDIX

9.5 Parameters (functions) and instruction codes under different control methods

Downloaded from ManualsNet.com
page 670.)
page 670.)
FR-A8TP, FR-A8APR,
FR-A8AVP, FR-A8NC,
Instruction
*1
code
Name
00 80
01 81
02 82
03 83
04 84
05 85
06 86
07 87
08 88
09 89
0A 8A
0B 8B
0C 8C
0D 8D
0E 8E
0F 8F
10 90
11 91
12 92
13 93
14 94
search engine
FR-A8APS, FR-A8APA,
FR-A8NCE, FR-A8NCG,
Control method
Vector Vector Vector
0 ○ × × ×
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ × × ×
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ × ×
0 ○ ○ ○ ○
0 ○ × × ×
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ ○ ○ ○
0 ○ × × ×
0 ○ ○ ○ ○
FR-A8AR,
FR-A8ND, FR-A8NP,
*2
*3
Sensorless Sensorless Sensorless PM PM PM
× × × × ×
○ ○ ○ ○ ○
× ○ ○ ○ ×
× × × × ×
Δ ○ ○ ○ Δ
Δ ○ ○ ○ Δ
Δ ○ ○ ○ Δ
Δ ○ ○ ○ Δ
Δ ○ ○ ○ Δ
○ ○ ○ ○ ○
× ○ ○ ○ ×
× ○ ○ ○ ×
× × × × ×
× ○ ○ ○ ×
× × × × ×
× ○ ○ ○ ×
× ○ ○ ○ ×
○ ○ ○ ○ ○
○ ○ ○ ○ ○
× × × × ×
Δ ○ ○ ○ Δ
FR-A8AX, FR-
FR-A8NF,
Parameter
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○