Mitsubishi Electric FR-A800 Series Instruction Manual page 475

Pr.
190 RUN terminal
M400 function selection
191 SU terminal function
M401 selection
192 IPF terminal function
M402 selection
193 OL terminal function
M403 selection
194 FU terminal function
M404 selection
195 ABC1 terminal
M405 function selection
196 ABC2 terminal
M406 function selection
313
DO0 output
*3*4
selection
M410
314
DO1 output
*3*4
selection
M411
315
DO2 output
*3*4
selection
M412
316
DO3 output
*3
selection
M413
317
DO4 output
*3
selection
M414
318
DO5 output
*3
selection
M415
319
DO6 output
*3
selection
M416
320
RA1 output selection
*3
M420
321
RA2 output selection
*3
M421
322
RA3 output selection
*3
M422
Pr.
289 Inverter output terminal
M431 filter
*1 The initial value is for standard models and IP55 compatible models.
*2 The initial value is for separated converter types.
*3 The setting is available when the PLC function is enabled or when a compatible plug-in option is installed.
*4 The setting is available for the FR-A800-GF.
 Output signal list
• A function listed below can be set to each output terminal.
• Refer to the following table and set the parameters. (0 to 99, 200 to 299: Positive logic, 100 to 199, 300 to 399: Negative
logic)
Setting
Positive Negative
logic logic
0 100
474
5. PARAMETERS
5.11 (M) Item and output signal for monitoring
Downloaded from ManualsNet.com
Initial
Name
value
0
1
For open
*1
2
collector
output
9999
terminal
3
4
99
For relay
output
terminal
9999
9999
9999
9999
9999
9999
For
terminal
on the
9999
option
9999
0
1
*1
2
9999
Initial
Name Setting range
value
5 to 50 ms
9999
9999
Signal
Function
name
RUN Inverter running
search engine
Signal name
RUN (Inverter running)
SU (Up to frequency)
IPF (Instantaneous power
failure/undervoltage)
*2
No function
OL (Overload warning)
FU (Output frequency
detection)
ALM (Fault)
No function
No function
No function
No function
No function
No function
No function
No function
RUN (Inverter running)
SU (Up to frequency)
IPF (Instantaneous power
failure/undervoltage)
*2
No function
Set the time delay for the output terminal response.
No filtering of the output terminal.
Operation
Outputted during operation when the inverter
output frequency reaches Pr.13 Starting
frequency or higher.
Setting range
0 to 8, 10 to 20, 22, 25 to 28, 30 to 36, 38 to 57,
60, 61, 63, 64, 67, 68, 70, 79, 80, 84, 85, 90 to
99, 100 to 108, 110 to 116, 120, 122, 125 to
128, 130 to 136, 138 to 157, 160, 161, 163,
164, 167, 168, 170, 179, 180, 184, 185, 190 to
199, 200 to 208, 211 to 213, 247, 300 to 308,
311 to 313, 347, 9999
0 to 8, 10 to 20, 22, 25 to 28, 30 to 36, 38 to 57,
60, 61, 63, 64, 67, 68, 70, 79, 80, 84, 85, 90, 91,
94 to 99, 100 to 108, 110 to 116, 120, 122, 125
to 128, 130 to 136, 138 to 157, 160, 161, 163,
164, 167, 168, 170, 179, 180, 184, 185, 190,
191, 194 to 199, 200 to 208, 211 to 213, 247,
300 to 308, 311 to 313, 347, 9999
0 to 8, 10 to 20, 22, 25 to 28, 30 to 36, 38 to 57,
60, 61, 63, 64, 68, 70, 79, 80, 84 to 99, 100 to
108, 110 to 116, 120, 122, 125 to 128, 130 to
136, 138 to 157, 160, 161, 163, 164, 168, 170,
179, 180, 184 to 199, 200 to 208, 211 to 213,
247, 248, 300 to 308, 311 to 313, 347, 348,
9999
0 to 8, 10 to 20, 22, 25 to 28, 30 to 36, 38 to 57,
60, 61, 63, 64, 68, 70, 79, 80, 84 to 91, 94 to 99,
200 to 208, 211 to 213, 247, 248, 9999
Description
Related
parameter
—
Refer
to
page
479