Toshiba GR200 Series Instruction Manual page 996

Table 4.9-32 Erroneous setting example for contact health check
Example #2
"TPOS01_P1SL_BO_FLG" is connected to "BO1" on SLOT1
"TPOS01_P2SL_BO_FLG" is connected to "BO2" on SLOT1
"TPOS01_P3SL_BO_FLG" is connected to "BO3" on SLOT1
"TPOS01_P1EX_BO" is connected to "BO4" on SLOT1
"TPOS01_P2EX_BO" is connected to "BO5" on SLOT1
"TPOS01_P3EX_BO" is connected to "BO6" on SLOT1
Remote/Local-end
"
TPOS01_P1SL_BO_FLG
(513001 8A04011DC4)
P1-select
command
"
TPOS01_P1EX_BO
(513001 8104011DD0)
P1-operate
command
"
TPOS01_P2SL_BO_FLG
(513001 8A04011DC6)
P2-select
command
"
TPOS01_P2EX_BO
(513001 8204011DD3)
P2-operate
command
"
TPOS01_P3SL_BO_FLG
(513001 8A04011DC8)
P3-select
command
"
TPOS01_P3EX_BO
(513001 8204031DD3)
P3-operate
command
Figure 4.9-62 Contact health check setting and EDS diagram for example #2
Setting for extra contact health check (special setting, example #3)
Figure 4.9-63 shows an additional setting example for the EDS scheme; one of the settings is
made hypothetically. That is, the point "SPO01_P1*SL_BO_FLG" is actually chosen for the
setting [TPOS01-P1*SLBORD]; i.e. BO1-RB is not chosen for this selection. This special
"BO1" (not BO1-RB)
BIO module
"
mistakenly chosen with
Drivers
200B01 8002001112
BO1
"
BO4
" "
BO4-RB
( 200B01 8302031113)
"
BO2
" "
BO2-RB
(
200B01 8102011113)
"
BO5
" "
BO5-RB
(
200B01 8402041113)
"
BO3
" "
BO3-RB
(
200B01 8202021113)
"
BO6
" "
BO6-RB
(
200B01 8502051113)
- 973 -
Health check setting for example #2
200B01 8002001112 (BO1) set for [TPOS01-P1SLBORD]
200B01 8102011113(BO2-RB) set for [TPOS01-P2SLBORD]
200B01 8202021113(BO3-RB) set for [TPOS01-P3SLBORD]
200B01 8302031113(BO4-RB) set for [TPOS01-P1EXBORD]
200B01 8402041113(BO5-RB) set for [TPOS01-P2EXBORD]
200B01 8502051113(BO6-RB) set for [TPOS01-P3EXBORD]
EDS
Plus (+)
P1-Selection
P1-Operate
6F2S1914 (0.49)
P3-Selection
P2-Selection
P2-Operate P3-Operate
Minus (−)
GRL200 (Soft 033 & 037)
NG
OK
OK
OK
OK
OK