Actual Signals; 01 Operating Data - ABB ACS350 User Manual

Actual signals

Actual signals
No. Name/Value

01 OPERATING DATA

0101 SPEED & DIR
0102 SPEED
0103 OUTPUT FREQ
0104 CURRENT
0105 TORQUE
0106 POWER
0107 DC BUS VOLTAGE
0109 OUTPUT VOLTAGE
0110 DRIVE TEMP
0111 EXTERNAL REF 1
0112 EXTERNAL REF 2
0113 CTRL LOCATION
0114 RUN TIME (R)
0115 KWH COUNTER (R)
0120 AI1
0121 AI2
0124 AO1
0126 PID 1 OUTPUT
0127 PID 2 OUTPUT
0128 PID 1 SETPNT
0129 PID 2 SETPNT
0130 PID 1 FBK
0131 PID 2 FBK
0132 PID 1 DEVIATION
Description
Basic signals for monitoring the drive (read-only)
Calculated motor speed in rpm. A negative value indicates reverse
direction.
Calculated motor speed in rpm
Calculated drive output frequency in Hz. (Shown by default on the panel
Output mode display.)
Measured motor current in A. (Shown by default on the panel Output
mode display.)
Calculated motor torque in percent of the motor nominal torque
Measured motor power in kW
Measured intermediate circuit voltage in VDC
Calculated motor voltage in VAC
Measured IGBT temperature in °C
External reference REF1 in rpm or Hz. Unit depends on parameter
MOTOR CTRL MODE setting.
External reference REF2 in percent. Depending on the use, 100% equals
the maximum motor speed, nominal motor torque, or maximum process
reference.
Active control location. (0) LOCAL; (1) EXT1; (2) EXT2. See section
control vs. external control
Elapsed drive running time counter (hours). The counter can be reset by
pressing the UP and DOWN buttons simultaneously when the control
panel is in Parameter mode.
kWh counter. The counter can be reset by pressing UP and DOWN
buttons simultaneously when the control panel is in Parameter mode.
Relative value of analog input AI1 in percent
Relative value of analog input AI2 in percent
Value of analog output AO in mA
Output value of the process PID1 controller in percent
Output value of the PID2 controller in percent
Setpoint signal (reference) for the process PID1 controller. Unit depends
on parameter 4006 UNIT,
SET settings.
Setpoint signal (reference) for the PID2 controller. Unit depends on
parameter 4106 UNIT and
Feedback signal for the process PID1 controller. Unit depends on
parameter 4006 UNIT, 4007
settings.
Feedback signal for the PID2 controller. Unit depends on parameter
UNIT and 4107 UNIT SCALE settings.
Deviation of the process PID1 controller, i.e. the difference between the
reference value and the actual value. Unit depends on parameter
UNIT, 4007 UNIT SCALE and
on page 97.
4007 UNIT SCALE and 4027
4107 UNIT SCALE settings.
UNIT SCALE and 4027
4027 PID 1 PARAM SET settings.
FbEq
1 = 1 rpm
1 = 1 rpm
1 = 0.1 Hz
1 = 0.1 A
1 = 0.1%
1 = 0.1 kW
1 = 1 V
1 = 1 V
1 = 0.1°C
9904 1 = 0.1 Hz /
1 rpm
1 = 0.1%
Local 1 = 1
1 = 1 h
1 = 1 kWh
1 = 0.1%
1 = 0.1%
1 = 0.1 mA
1 = 0.1%
1 = 0.1%
-
PID 1 PARAM
-
-
PID 1 PARAM SET
-
4106
-
4006
Actual signals and parameters
143