ABB ACS350 User Manual page 156

156
Parameters – short form list
Index Name/Selection
42 EXT / TRIM PID
4201 GAIN
4202 INTEGRATION TIME
4203 DERIVATION TIME
4204 PID DERIV FILTER
4205 ERROR VALUE INV
4206 UNITS
4207 UNIT SCALE
4208 0% VALUE
4209 100% VALUE
4210 SET POINT SEL
4211 INTERNAL SETPNT
4212 SETPOINT MIN
4213 SETPOINT MAX
4214 FBK SEL
4215 FBK MULTIPLIER
4216 ACT1 INPUT
4217 ACT2 INPUT
4218 ACT1 MINIMUM
4219 ACT1 MAXIMUM
4220 ACT2 MINIMUM
4221 ACT2 MAXIMUM
4228 ACTIVATE
4229 OFFSET
4230 TRIM MODE
4231 TRIM SCALE
4232 CORRECTION SRC
4233 TRIM SELECTION
43 MECH BRK CONTROL Control of a mechanical brake.
4301 BRAKE OPEN DLY
4302 BRAKE OPEN LVL
4303 BRAKE CLOSE LVL
4304 FORCED OPEN LVL
4305 BRAKE MAGN DELAY Defines motor magnetising time.
4306 RUNTIME FREQ LVL
50 ENCODER
5001 PULSE NR
5002 ENCODER ENABLE
5003 ENCODER FAULT
5010 Z PLS ENABLE
5011 POSITION RESET
51 EXT COMM MODULE
5101 FBA TYPE
5102 FB PAR 2
... ....
5126 FB PAR 26
Actual signals and parameters
Description
External/Trim PID (PID2) control.
See parameter 4001 GAIN.
See parameter 4002 INTEGRATION TIME.
See parameter 4003 DERIVATION TIME.
See parameter 4004 PID DERIV FILTER.
See parameter 4005 ERROR VALUE INV.
See parameter 4006 UNITS.
See parameter 4007 UNIT SCALE.
See parameter 4008 0% VALUE.
See parameter 4009 100% VALUE.
See parameter 4010 SET POINT SEL.
See parameter 4011 INTERNAL SETPNT.
See parameter 4012 SETPOINT MIN.
See parameter 4013 SETPOINT MAX.
See parameter 4014 FBK SEL.
See parameter 4015 FBK MULTIPLIER.
See parameter 4016 ACT1 INPUT.
See parameter 4017 ACT2 INPUT.
See parameter 4018 ACT1 MINIMUM.
See parameter 4018 ACT1 MAXIMUM.
See parameter 4020 ACT2 MINIMUM.
See parameter 4021 ACT2 MAXIMUM.
Selects the source for the external PID function activation signal.
Defines the offset for the external PID controller output.
Activates the trim function and selects between the direct and
proportional trimming.
Defines the multiplier for the trimming function.
Selects the trim reference.
Selects whether the trimming is used for correcting the speed or
torque reference.
Defines the brake open delay (= the delay between the internal
open brake command and the release of the motor speed
control).
Defines the motor starting torque/current at brake release.
Defines the brake close speed.
Defines the speed at brake release.
Defines the brake close speed.
Encoder connection.
States the number of encoder pulses per one revolution.
Enables the encoder.
Defines the operation of the drive if a failure is detected in
communication between the pulse encoder and the pulse
encoder interface module, or between the module and the drive.
Enables the encoder zero (Z) pulse. Zero pulse is used for
position reset.
Enables the position reset.
Fieldbus adapter module parameters.
Displays the type of the connected fieldbus adapter module.
These parameters are adapter module-specific.
Def Custom
NOT SEL
0
NOT SEL
0
PID2REF
SPEED/FREQ
0.20
1
4.0%
0
0
0
1024
DISABLE
FAULT
DISABLE
DISABLE