ABB ACS350 User Manual page 158

158
Parameters – short form list
Index Name/Selection
8403 SEQ PROG PAUSE
8404 SEQ PROG RESET
8405 SEQ ST FORCE
8406 SEQ LOGIC VAL 1
8407 SEQ LOGIC OPER 1
8408 SEQ LOGIC VAL 2
8409 SEQ LOGIC OPER 2
8410 SEQ LOGIC VAL 3
8411 SEQ VAL 1 HIGH
8412 SEQ VAL 1 LOW
8413 SEQ VAL 2 HIGH
8414 SEQ VAL 2 LOW
8415 CYCLE CNT LOC
8416 CYCLE CNT RST
8420 ST1 REF SEL
8421 ST1 COMMANDS
8422 ST1 RAMP
8423 ST1 OUT CONTROL
8424 ST1 CHANGE DLY
8425 ST1 TRIG TO ST 2
8426 ST1 TRIG TO ST N
8427 ST1 STATE N
8430 ST2 REF SEL
...
8497 ST8 STATE N
98 OPTIONS
9802 COMM PROT SEL
99 START-UP DATA
9901 LANGUAGE
9902 APPLIC MACRO
9904 MOTOR CTRL MODE
9905 MOTOR NOM VOLT
9906 MOTOR NOM CURR
9907 MOTOR NOM FREQ
9908 MOTOR NOM SPEED
9909 MOTOR NOM POWER Defines the nominal motor power.
9910 ID RUN
9912 MOTOR NOM TORQUE Calculated motor nominal torque in Nm.
9913 MOTOR POLE PAIRS
Actual signals and parameters
Description
Selects the source for the sequence programming pause signal.
Selects the source for the sequence programming reset signal.
Forces the sequence programming to a selected state.
Defines the source for the logic value 1.
Selects the operation between logic value 1 and 2.
See parameter 8406 SEQ LOGIC VAL 1.
Selects the operation between logic value 3 and the result of the
first logic operation defined by parameter 8407 SEQ LOGIC
OPER 1.
See parameter 8406 SEQ LOGIC VAL 1.
Defines the high limit for the state change when parameter 8425
ST1 TRIG TO ST 2 is set to e.g. AI1 HIGH 1.
Defines the low limit for the state change when parameter 8425
ST1 TRIG TO ST 2 is set to e.g. AI1 LOW 1.
Defines the high limit for the state change when parameter 8425
ST1 TRIG TO ST 2 is set to e.g. AI2 HIGH 1.
Defines the low limit for the state change when parameter 8425
ST1 TRIG TO ST 2 is set to e.g. AI2 LOW 2.
Activates the cycle counter for sequence programming.
Selects the source for the cycle counter reset signal (0171 SEQ
CYCLE CNTR).
Selects the source for the sequence programming state 1
reference.
Selects the start, stop and direction for state 1.
Selects the acceleration/deceleration ramp time for sequence
programming state 1, i.e. defines the rate of the reference
change.
Selects the relay, transistor and analog output control for
sequence programming state 1.
Defines the delay time for state 1.
Selects the source for the trigger signal which changes the state
from state 1 to state 2.
Selects the source for the trigger signal which changes the state
from state 1 to state N.
Defines the state N. See parameter 8426 ST1 TRIG TO ST N.
See parameters 8420...8427.
External serial communication activation
Activates the external serial communication.
Language selection. Definition of motor set-up data.
Selects the display language.
Selects the application macro.
Selects the motor control mode.
Defines the nominal motor voltage.
Defines the nominal motor current.
Defines the nominal motor frequency.
Defines the nominal motor speed.
Controls a self-calibration process called the Motor ID Run.
Calculated motor pole pair number.
Def Custom
NOT SEL
NOT SEL
STATE1
NOT SEL
NOT SEL
NOT SEL
NOT SEL
NOT SEL
0
0
0
0
NOT SEL
NOT SEL
0
DRIVE STOP
0
AO=0
0
NOT SEL
NOT SEL
STATE 1
NOT SEL
ENGLISH
ABB STANDARD
SCALAR:FREQ
230, 400 or 460
I2N
Eur: 50 / US: 60
Type dependent
PN
OFF/IDMAGN
0
0