Husqvarna 701 Enduro 2017 Repair Manual page 262

26 TECHNICAL DATA
260
Coolant temperature: > 70 °C (> 158 °F)
Engine speed: 1,500 rpm
> 0.4 bar (> 6 psi)
Coolant temperature: > 70 °C (> 158 °F)
Engine speed: 5,000 rpm
>1.5 bar (> 22 psi)
0.10... 0.40 mm (0.0039... 0.0157 in) Main shaft axial clearance
Transmission shaft run-out < 0.025 mm (< 0.00098 in)
Shift shaft - play in sliding plate/shift quadrant 0.40... 0.80 mm (0.0157... 0.0315 in)
Fuel pressure
3.3... 3.7 bar (48... 54 psi) Under every load condition
26.3 Engine tightening torques
Loctite® 243™ Screw, membrane fixation M3 2 Nm (1.5 Ibf ft)
Hose clamp, intake flange M4 2.5 Nm (1.84 Ibf ft)
Loctite® 243™ Oil nozzle for conrod bearing lubrica-
tion
2 Nm (1.5 Ibf ft) M4
Loctite® 243™ 6 Nm (4.4 Ibf ft) Locking screw for bearing M5
6 Nm (4.4 Ibf ft) Remaining screws, engine M5
Loctite® 243™ Screw, axial lock of camshaft M5 6 Nm (4.4 Ibf ft)
Loctite® 243™ Screw, breather cover on valve cover M5 6 Nm (4.4 Ibf ft)
Screw, clutch spring 6 Nm (4.4 Ibf ft) M5
Screw, cover plate for oil return line 6 Nm (4.4 Ibf ft) M5
Loctite® 243™ Screw, gear sensor 5 Nm (3.7 Ibf ft) M5
Screw, oil filter cover M5 6 Nm (4.4 Ibf ft)
Loctite® 243™ Screw, oil pump cover, top M5 6 Nm (4.4 Ibf ft)
Loctite® 243™ 10 Nm (7.4 Ibf ft) Plug, vacuum connection M6
10 Nm (7.4 Ibf ft) Remaining screws, engine M6
Screw in alternator cover M6 10 Nm (7.4 Ibf ft)
Loctite® 243™ Screw, alternator cover (chain shaft
through-hole)
M6 10 Nm (7.4 Ibf ft)
Loctite® 243™ Screw, auto decompression M6 3.5 Nm (2.58 Ibf ft)
Screw, clutch cover 10 Nm (7.4 Ibf ft)
M6
Loctite® 243™ Screw, clutch slave cylinder 10 Nm (7.4 Ibf ft) M6x20
Screw, clutch slave cylinder 10 Nm (7.4 Ibf ft) M6x35
Loctite® 243™ Screw, cylinder M6 10 Nm (7.4 Ibf ft)
Loctite® 243™ Screw, cylinder head M6 10 Nm (7.4 Ibf ft)
Screw, engine case 10 Nm (7.4 Ibf ft) M6
Screw, ignition coil M6 10 Nm (7.4 Ibf ft)
Loctite® 243™
Screw, ignition pulse generator 10 Nm (7.4 Ibf ft)
M6
Loctite® 243™
Screw, locking lever 10 Nm (7.4 Ibf ft) M6
Loctite® 243™ Screw, oil pump cover, bottom M6 10 Nm (7.4 Ibf ft)
Screw, rocker arm shaft
M6 12 Nm (8.9 Ibf ft)
Loctite® 243™ Screw, shift drum locating 10 Nm (7.4 Ibf ft) M6
Loctite® 243™ Screw, shift lever 14 Nm (10.3 Ibf ft) M6
Loctite® 243™ Screw, starter motor 10 Nm (7.4 Ibf ft) M6
Loctite® 243™ Screw, stator M6 10 Nm (7.4 Ibf ft)
Loctite® 243™ Screw, thermostat housing M6 10 Nm (7.4 Ibf ft)
Loctite® 2701™ Screw, timing chain guide rail 10 Nm (7.4 Ibf ft) M6x30
Loctite® 2701™ Screw, timing chain tensioning rail 10 Nm (7.4 Ibf ft) M6x30
Screw, valve cover 10 Nm (7.4 Ibf ft) M6
Screw, water pump cover M6 10 Nm (7.4 Ibf ft)
Loctite® 243™ Screw, water pump wheel M6 10 Nm (7.4 Ibf ft)
Loctite® 243™ Oil jet, piston cooling 4 Nm (3 Ibf ft) M6x0.75